FPGA Interface Manager Developer Guide for Open FPGA Stack: Agilex® 7 FPGA I-Series Development Kit (2x R-Tile and 1xF-Tile) PCIe Attach

Last updated: November 19, 2024

1. Introduction

1.1. About This Document

This document serves as a guide for OFS Agilex PCIe Attach developers targeting the Agilex® 7 FPGA I-Series Development Kit (2x R-Tile and 1xF-Tile). The following topics are covered in this guide:

• Compiling the OFS Agilex PCIe Attach FIM design
• Simulating the OFS Agilex PCIe Attach design
• Customizing the OFS Agilex PCIe Attach FIM design
• Configuring the FPGA with an OFS Agilex PCIe Attach FIM design

The FIM Development Walkthroughs Table lists all of the walkthroughs provided in this guide. These walkthroughs provide step-by-step instructions for performing different FIM Development tasks.

Table: FIM Development Walkthroughs

Walkthrough Name	Category
Install Quartus Prime Pro Software	Setup
Clone FIM Repository	Setup
Set Development Environment Variables	Setup
Set Up Development Environment	Setup
Compile OFS FIM	Compilation
Manually Generate OFS Out-Of-Tree PR FIM	Compilation
Change the Compilation Seed	Compilation
Running Individual Unit Level Simulation	Simulation
Running Regression Unit Level Simulation	Simulation
Add a new module to the OFS FIM	Customization
Modify and run unit tests for a FIM that has a new module	Customization
Hardware test a FIM that has a new module	Customization
Debug the FIM with Signal Tap	Customization
Compile the FIM in preparation for designing your AFU	Customization
Resize the Partial Reconfiguration Region	Customization
Modify the PCIe Sub-System and PF/VF MUX Configuration Using OFSS	Customization
Modify PCIe Configuration Using IP Presets	Customization
Migrate to a Different Agilex Device Number	Customization
Modify the Ethernet Sub-System to 1x400GbE	Customization
Set up JTAG	Configuration
Program the FPGA via JTAG	Configuration

1.1.1 Knowledge Pre-Requisites

It is recommended that you have the following knowledge and skills before using this developer guide.

• Basic understanding of OFS and the difference between OFS designs. Refer to the OFS Welcome Page.
• Review the release notes for the Agilex 7 PCIe Attach Reference Shells, with careful consideration of the Known Issues.
• Review of Getting Started Guide: OFS for Agilex® 7 PCIe Attach FPGAs (I-Series Development Kit (2xR-Tile, 1xF-Tile))
• FPGA compilation flows using Quartus® Prime Pro Edition.
• Static Timing closure, including familiarity with the Timing Analyzer tool in Quartus® Prime Pro Edition, applying timing constraints, Synopsys* Design Constraints (.sdc) language and Tcl scripting, and design methods to close on timing critical paths.
• RTL (System Verilog) and coding practices to create synthesized logic.
• RTL simulation tools.
• Quartus® Prime Pro Edition Signal Tap Logic Analyzer tool software.

1.2. FIM Development Theory

This section will help you understand how the OFS Agilex PCIe Attach FIM can be developed to fit your design goals.

The Default FIM Features section provides general information about the default features of the OFS Agilex PCIe Attach FIM so you can become familiar with the default design. For more detailed information about the FIM architecture, refer to the Shell Technical Reference Manual: OFS for Agilex® 7 PCIe Attach FPGAs.

The Customization Options section then gives suggestions of how this default design can be customized. Step-by-step walkthroughs for many of the suggested customizations are later described in the FIM Customization section.

FIM development for a new acceleration card generally consists of the following steps:

1. Install OFS and familiarize yourself with provided scripts and source code
2. Develop high level design with your specific functionality
   1. Determine requirements and key performance metrics
   2. Select IP cores
   3. Select FPGA device
   4. Develop software memory map
3. Select and implement FIM Physical interfaces including:
   1. External clock sources and creation of internal PLL clocks
   2. General I/O
   3. Ethernet modules
   4. External memories
   5. FPGA programming methodology
4. Develop device physical implementation
   1. FPGA device pin assignment
   2. Create logic lock regions
   3. Create of timing constraints
   4. Create Quartus Prime Pro FIM test project and validate:
      1. Placement
      2. Timing constraints
      3. Build script process
      4. Review test FIM FPGA resource usage
5. Select FIM to AFU interfaces and development of PIM
6. Implement FIM design
   1. Develop RTL
   2. Instantiate IPs
   3. Develop test AFU to validate FIM
   4. Develop unit and device level simulation
   5. Develop timing constraints and build scripts
   6. Perform timing closure and build validation
7. Create FIM documentation to support AFU development and synthesis
8. Software Device Feature discovery
9. Integrate, validate, and debug hardware/software
10. Prepare for high volume production

1.2.1 Default FIM Features

1.2.1.1 Top Level

Figure: OFS Agilex PCIe Attach iseries-dk FIM PCIe 1x16 Top-Level Diagram

Figure: OFS Agilex PCIe Attach iseries-dk FIM PCIe 2x8 Top-Level Diagram

1.2.1.2 Interfaces

The key interfaces in the OFS Agilex PCIe Attach design are listed in the Release Capabilities Table. It describes the capabilities of the iseries-dk hardware as well as the capabilities of the default OFS Agilex PCIe Attach design targeting the iseries-dk.

Table: Release Capabilities

Interface	iseries-dk Hardware Capabilities1	OFS Agilex PCIe Attach Provided Design Implementation
Host Interface	PCIe Gen5x16	• PCIe 1xGen5x16 (Default) • Bifurcated PCIe 2xGen5x8 • PCIe 1xGen4x16
Network Interface	2 - QSFP-DD	3 Build Options: 1. QSFP 1,0 = 25 GbE 2. QSFP 1,0 = 200 GbE 3. QSFP 0 = 400 GbE
External Memory	2 - board mounted independent single rank DDR4-2666 8GB (1 Gb x 64 + 8b ECC) 2 - DIMM sockets where each socket is single memory channels or independent channels (Check Dev Kit OPN for support option)2.	4xDDR4-2666 - 8GB (1Gb x 64 bits) - ECC not implemented by default

¹ The iseries-dk FIM design was validated on DK-DEV-AGI027RBES with Agilex 7 device number AGIB027R29A1E2VR3. If you wish to use the production develpment kit (DK-DEV-AGI027-RA), you will need to migrate to device number AGIB027R29A1E1VB. Refer to the Migrate to a Different Agilex Device Number section for general instructions on this process.

² The iseries-dk was validated with 2 Micron MTA8ATF1G64AZ-2G6E1 DDR4 SDRAM modules in the DIMM sockets.

1.2.1.3 Subsystems

The FIM Subsystems Table describes the Platform Designer IP subsystems used in the OFS Agilex PCIe Attach iseries-dk FIM.

Table: FIM Subsystems

Subsystem	User Guide	Document ID
PCIe Subsystem	AXI Streaming IP for PCI Express User Guide	790711
Memory Subsystem	Memory Subsystem Intel FPGA IP User Guide for Intel Agilex OFS	686148[1]
Ethernet Subsystem	Ethernet Subsystem Intel FPGA IP User Guide	773413[1]

^[1] You must request entitled access to these documents.

1.2.1.4 Host Exercisers

The default AFU workload in the OFS Agilex PCIe Attach iseries-dk FIM contains several modules called Host Exercisers which are used to exercise the interfaces on the board. The Host Exerciser Descriptions Table describes these modules.

Table: Host Exerciser Descriptions

Name	Acronym	Description	OPAE Command
Host Exerciser Loopback	HE-LB	Used to exercise and characterize host to FPGA data transfer.	host_exerciser
Host Exerciser Memory	HE_MEM	Used to exercise and characterize host to Memory data transfer.	host_exerciser
Host Exerciser Memory Traffic Generator	HE_MEM_TG	Used to exercise and test available memory channels with a configurable traffic pattern.	mem_tg
Host Exerciser High Speed Serial Interface	HE-HSSI	Used to exercise and characterize HSSI interfaces.	hssi

The host exercisers can be removed from the design at compile-time using command line arguments for the build script.

1.2.1.5 Module Access via APF/BPF

The OFS Agilex PCIe Attach iseries-dk FIM uses AXI4-Lite interconnect logic named the AFU Peripheral Fabric (APF) and Board Peripheral Fabric (BPF) to access the registers of the various modules in the design. The APF/BPF modules define master/slave interactions, namely between the host software and AFU and board peripherals. The APF Address Map Table describes the address mapping of the APF, followed by the BPF Address Map Table which describes the address mapping of the BPF.

Table: APF Address Map

Address	Size (Bytes)	Feature
0x00000–0x3FFFF	256K	Board Peripherals (See BPF Address Map table)
0x40000 – 0x4FFFF	64K	ST2MM
0x50000 – 0x5FFFF	64K	Reserved
0x60000 – 0x60FFF	4K	UART (not used)
0x61000 – 0x6FFFF	4K	Reserved
0x70000 – 0x7FFFF	56K	PR Gasket:4K= PR Gasket DFH, control and status4K= Port DFH4K=User Clock52K=Remote STP
0x80000 – 0x80FFF	4K	AFU Error Reporting

Table: BPF Address Mapping

Address	Size (Bytes)	Feature
0x00000 - 0x0FFFF	64K	FME
0x10000 - 0x10FFF	4K	PCIe
0x11000 - 0x11FFF	4K	Reserved
0x12000 - 0x12FFF	4K	QSFP0
0x13000 - 0x13FFF	4K	QSFP1
0x14000 - 0x14FFF	4K	HSSI
0x15000 - 0x15FFF	4K	EMIF
0x20000 - 0x3FFFF	128K	PMCI (note, PMCI is not implemented)

1.2.2 Customization Options

OFS is designed to be easily customizable to meet your design needs. The OFS FIM Customizations Table lists the general user flows for OFS Agilex PCIe Attach iseries-dk FIM development, along with example customizations for each user flow, plus links to step-by-step walkthroughs where available.

Table: OFS FIM Customizations

Customization Walkthrough Name
Add a new module to the OFS FIM
Modify and run unit tests for a FIM that has a new module
Hardware test a FIM that has a new module
Debug the FIM with Signal Tap
Compile the FIM in preparation for designing your AFU
Resize the Partial Reconfiguration Region
Modify the PCIe Sub-System and PF/VF MUX Configuration Using OFSS
Modify PCIe Configuration Using IP Presets
Migrate to a Different Agilex Device Number
Modify the Ethernet Sub-System to 1x400GbE

1.3 Development Environment

This section describes the components required for OFS FIM development, and provides a walkthrough for setting up the environment on your development machine.

Note that your development machine may be different than your deployment machine where the FPGA acceleration card is installed. FPGA development work and deployment work can be performed either on the same machine, or on different machines as desired. Please see the Getting Started Guide: OFS for Agilex® 7 PCIe Attach FPGAs (I-Series Development Kit (2xR-Tile, 1xF-Tile)) for instructions on setting up the environment for deployment machines.

1.3.1 Development Tools

The Development Environment Table describes the Best Known Configuration (BKC) for the tools that are required for OFS FIM development.

Table: Development Environment BKC

Component	Version	Installation Walkthrough
Operating System	RedHat® Enterprise Linux® (RHEL) 8.10	N/A
Quartus Prime Software	Quartus Prime Pro Version 24.1 for Linux + Patches 0.18, 0.26	Section 1.3.1.1
Python	3.6.8 or later	N/A
GCC	8.5.0 or later	N/A
cmake	3.15 or later	N/A
git	1.8.3.1 or later	Section 1.3.1.2
FIM Source Files	ofs-2024.2-1	Section 1.3.2.1

1.3.1.1 Walkthrough: Install Quartus Prime Pro Software

Intel Quartus Prime Pro Version 24.1 is verified to work with the latest OFS release ofs-2024.2-1. However, you have the option to port and verify the release on newer versions of Intel Quartus Prime Pro software.

Use RedHat® Enterprise Linux® (RHEL) 8.10 for compatibility with your development flow and also testing your FIM design in your platform.

Prior to installing Quartus:

1. Ensure you have at least 64 GB of free space for Quartus Prime Pro installation and your development work.

   • Intel® recommends that your system be configured to provide virtual memory equal in size or larger than the recommended physical RAM size that is required to process your design.
   • The disk space may be significantly more based on the device families included in the install. Prior to installation, the disk space should be enough to hold both zipped tar files and uncompressed installation files. After successful installation, delete the downloaded zipped files and uncompressed zip files to release the disk space.

2. Perform the following steps to satisfy the required dependencies.

   $ sudo dnf install -y gcc gcc-c++ make cmake libuuid-devel rpm-build autoconf automake bison boost boost-devel libxml2 libxml2-devel make ncurses grub2 bc csh flex glibc-locale-source libnsl ncurses-compat-libs 
   

   Apply the following configurations.

   $ sudo localedef -f UTF-8 -i en_US en_US.UTF-8 
   $ sudo ln -s /usr/lib64/libncurses.so.6 /usr/lib64/libncurses.so.5 
   $ sudo ln -s /usr/bin/python3 /usr/bin/python
   

3. Create the default installation path: /intelFPGA_pro/, where is the default path of the Linux workstation, or as set by the system administrator and is your Quartus version number.

   The installation path must satisfy the following requirements:

   • Contain only alphanumeric characters
   • No special characters or symbols, such as !$%@^&*<>,
   • Only English characters
   • No spaces

4. Download your required Quartus Prime Pro Linux version here.

5. Install required Quartus patches. The Quartus patch .run files can be found in the Assets tab on the OFS Release GitHub page. The patches for this release are 0.18, 0.26.

6. After running the Quartus Prime Pro installer, set the PATH environment variable to make utilities quartus, jtagconfig, and quartus_pgm discoverable. Edit your bashrc file ~/.bashrc to add the following line:

   export PATH=<Quartus install directory>/quartus/bin:$PATH
   export PATH=<Quartus install directory>/qsys/bin:$PATH
   

   For example, if the Quartus install directory is /home/intelFPGA_pro/24.1 then the new line is:

   export PATH=/home/intelFPGA_pro/24.1/quartus/bin:$PATH
   export PATH=/home/intelFPGA_pro/24.1/qsys/bin:$PATH
   

7. Verify, Quartus is discoverable by opening a new shell:

   $ which quartus
   /home/intelFPGA_pro/24.1/quartus/bin/quartus
   

1.3.2 FIM Source Files

The source files for the OFS Agilex PCIe Attach FIM are provided in the following repository: https://github.com/OFS/ofs-agx7-pcie-attach/releases/tag/ofs-2024.2-1

Some essential directories in the repository are described as follows:

ofs-agx7-pcie-attach
|  syn                      // Contains files related to synthesis
|  |  board                     // Contains synthesis files for several cards, including the iseries-dk 
|  |  |  iseries-dk                 // Contains synthesis files for iseries-dk
|  |  |  |  setup                       // Contains setup files, including pin constraints and location constraints
|  |  |  |  syn_top                     // Contains Quartus project files
|  verification             // Contains files for UVM testing
|  ipss                     // Contains files for IP Sub-Systems
|  |  qsfp                      // Contains source files for QSFP Sub-System
|  |  hssi                      // Contains source files for HSSI Sub-System
|  |  pmci                      // Contains source files for PMCI Sub-System (not used in F-Tile FIM)
|  |  pcie                      // Contains source files for PCIe Sub-System
|  |  mem                       // Contains source files for Memory Sub-System
|  sim                      // Contains simulation files
|  |  unit_test                 // Contains files for all unit tests
|  |  |  scripts                    // Contains script to run regression unit tests
|  license                  // Contains Quartus patch
|  ofs-common               // Contains files which are common across OFS platforms
|  |  verification              // Contains common UVM files
|  |  scripts                   // Contains common scripts
|  |  |  common
|  |  |  |  syn                         // Contains common scripts for synthesis, including build script
|  |  |  |  sim                         // Contains common scripts for simulation
|  |  tools                     // Contains common tools files
|  |  |  mk_csr_module              // Contains common files for CSR modules
|  |  |  fabric_generation          // Contains common files for APF/BPF fabric generation
|  |  |  ofss_config                // Contains common files for OFSS configuration tool
|  |  |  |  ip_params                   // Contains default IP parameters for certain Sub-Systems when using OFSS
|  |  src                       // Contains common source files, including host exercisers
|  tools                    //
|  |  ofss_config               // Contains top level OFSS files for each pre-made board configuration
|  |  |  hssi                       // Contains OFSS files for Ethernet-SS configuraiton
|  |  |  memory                     // Contains OFSS files for Memory-SS configuration
|  |  |  pcie                       // Contains OFSS files for PCIe-SS configuration
|  |  |  iopll                      // Contains OFSS files for IOPLL configuration
|  src                      // Contains source files for Agilex PCIe Attach FIM
|  |  pd_qsys                   // Contains source files related to APF/BPF fabric
|  |  includes                  // Contains source file header files
|  |  top                       // Contains top-level source files, including design top module
|  |  afu_top                   // Contains top-level source files for AFU

1.3.2.1 Walkthrough: Clone FIM Repository

Perform the following steps to clone the OFS Agilex® 7 PCIe Attach FIM Repository:

1. Create a new directory to use as a clean starting point to store the retrieved files.

   mkdir OFS_BUILD_ROOT
   cd OFS_BUILD_ROOT
   export OFS_BUILD_ROOT=$PWD
   

2. Clone GitHub repository using the HTTPS git method

   git clone --recurse-submodules https://github.com/OFS/ofs-agx7-pcie-attach.git
   

3. Check out the correct tag of the repository

   cd ofs-agx7-pcie-attach
   git checkout --recurse-submodules tags/ofs-2024.2-1
   

4. Ensure that ofs-common has been cloned as well

   git submodule status
   

   Example output:

   ofs-common (ofs-2024.2-1)
   

1.3.3 Environment Variables

The OFS FIM compilation and simulation scripts require certain environment variables be set prior to execution.

1.3.3.1 Walkthrough: Set Development Environment Variables

Perform the following steps to set the required environment variables. These environment variables must be set prior to simulation or compilation tasks so it is recommended that you create a script to set these variables.

1. Navigate to the top level directory of the cloned OFS FIM repository.

   cd ofs-agx7-pcie-attach
   

2. Set project variables

   # Set OFS Root Directory - e.g. this is the top level directory of the cloned OFS FIM repository
   export OFS_ROOTDIR=$PWD
   

3. Set variables based on your development environment

   # Set proxies if required for your server
   export http_proxy=<YOUR_HTTP_PROXY>
   export https_proxy=<YOUR_HTTPS_PROXY>
   export ftp_proxy=<YOUR_FTP_PROXY>
   export socks_proxy=<YOUR_SOCKS_PROXY>
   export no_proxy=<YOUR_NO_PROXY>
   
   # Set Quartus license path
   export LM_LICENSE_FILE=<YOUR_LM_LICENSE_FILE>
   
   # Set Synopsys License path (if using Synopsys for simulation)
   export DW_LICENSE_FILE=<YOUR_DW_LICENSE_FILE>
   export SNPSLMD_LICENSE_FILE=<YOUR_SNPSLMD_LICENSE_FILE>
   
   # Set Quartus Installation Directory - e.g. $QUARTUS_ROOTDIR/bin contains Quartus executables
   export QUARTUS_ROOTDIR=<YOUR_QUARTUS_INSTALLATION_DIRECTORY>
   
   # Set the Tools Directory - e.g. $TOOLS_LOCATION contains the 'synopsys' directory if you are using Synopsys. Refer to the $VCS_HOME variable for an example.
   export TOOLS_LOCATION=<YOUR_TOOLS_LOCATION>
   

4. Set generic environment variables

   # Set Work directory 
   export WORKDIR=$OFS_ROOTDIR
   
   # Set Quartus Tools variables
   export QUARTUS_HOME=$QUARTUS_ROOTDIR
   export QUARTUS_INSTALL_DIR=$QUARTUS_ROOTDIR
   export QUARTUS_ROOTDIR_OVERRIDE=$QUARTUS_ROOTDIR
   export QUARTUS_VER_AC=$QUARTUS_ROOTDIR
   export IP_ROOTDIR=$QUARTUS_ROOTDIR/../ip
   export IMPORT_IP_ROOTDIR=$IP_ROOTDIR
   export QSYS_ROOTDIR=$QUARTUS_ROOTDIR/../qsys/bin
   
   # Set Verification Tools variables (if running simulations)
   export DESIGNWARE_HOME=$TOOLS_LOCATION/synopsys/vip_common/vip_Q-2020.03A
   export UVM_HOME=$TOOLS_LOCATION/synopsys/vcsmx/${{ env.ISERIES_DK_SIM_VCS_VER_SH }}/linux64/rhel/etc/uvm
   export VCS_HOME=$TOOLS_LOCATION/synopsys/vcsmx/${{ env.ISERIES_DK_SIM_VCS_VER_SH }}/linux64/rhel
   export MTI_HOME=$QUARTUS_ROOTDIR/../questa_fse
   export VERDIR=$OFS_ROOTDIR/verification
   export VIPDIR=$VERDIR
   
   # Set OPAE variables
   export OPAE_SDK_REPO_BRANCH=release/2.13.0
   
   # Set PATH to include compilation and simulation tools
   export PATH=$QUARTUS_HOME/bin:$QUARTUS_HOME/../qsys/bin:$QUARTUS_HOME/sopc_builder/bin/:$OFS_ROOTDIR/opae-sdk/install-opae-sdk/bin:$MTI_HOME/linux_x86_64/:$MTI_HOME/bin/:$DESIGNWARE_HOME/bin:$VCS_HOME/bin:$PATH
   

1.3.4 Walkthrough: Set Up Development Environment

This walkthrough guides you through the process of setting up your development environment in preparation for FIM development. This flow only needs to be done once on your development machine.

1. Ensure that Quartus Prime Pro Version 24.1 for Linux with Agilex FPGA device support is installed on your development machine. Refer to the Install Quartus Prime Pro Software section for step-by-step installation instructions.

   1. Verify version number

      quartus_sh --version
      

      Example Output:

      Quartus Prime Shell
      Version 24.1 Build 94 06/14/2023 SC Pro Edition
      

2. Ensure that all support tools are installed on your development machine, and that they meet the version requirements.

   1. Python 3.6.8 or later

      1. Verify version number

         python --version
         

         Example Output:

         Python 3.6.8
         

   2. GCC 8.5.0 or later

      1. Verify version number

         gcc --version
         

         Example output:

         gcc (GCC) 8.5.0
         

   3. cmake 3.15 or later

      1. Verify version number

         cmake --version
         

         Example output:

         cmake version 3.15
         

   4. git 1.8.3.1 or later.

      1. Verify version number

         git --version
         

         Example output:

         git version 1.8.3.1
         

3. Clone the ofs-agx7-pcie-attach repository. Refer to the Clone FIM Repository section for step-by-step instructions.

4. Install UART IP license patch .02.

   1. Navigate to the license directory

      cd $IOFS_BUILD_ROOT/license
      

   2. Install Patch 0.02

      sudo ./quartus-0.0-0.02iofs-linux.run
      

5. Install Quartus Patches 0.18, 0.26. All required patches are provided in the Assets of the OFS FIM Release Tag: https://github.com/OFS/ofs-agx7-pcie-attach/releases/tag/ofs-2024.2-1

   1. Extract and unzip the patch-agx7-2024-1.tar.gz file.

      tar -xvzf patch-agx7-2024-1.tar.gz
      

   2. Run each patch .run file. As an example:

      sudo ./quartus-23.4-0.17-linux.run
      

6. Verify that patches have been installed correctly. They should be listed in the output of the following command.

   quartus_sh --version
   

7. Set required environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

This concludes the walkthrough for setting up your development environment. At this point you are ready to begin FIM development.

2. FIM Compilation

This section describes the process of compiling OFS FIM designs using the provided build scripts. It contains two main sections:

• Compilation Theory - Describes the theory behind FIM compilation
• Compilation Flows - Describes the process of compiling a FIM

The walkthroughs provided in this section are:

• Compile OFS FIM
• Manually Generate OFS Out-Of-Tree PR FIM
• Change the Compilation Seed

2.1 Compilation Theory

This section describes the theory behind FIM compilation.

2.1.1 FIM Build Script

The OFS Common Repository contains a script named build_top.sh which is used to build OFS FIM designs and generate output files that can be programmed to the board. After cloning the OFS FIM repository (with the ofs-common repository included), the build script can be found in the following location:

$OFS_ROOTDIR/ofs-common/scripts/common/syn/build_top.sh

The usage of the build_top.sh script is as follows:

build_top.sh [-k] [-p] [-e] [--stage=<action>] [--ofss=<ip_config>] <build_target>[:<fim_options>] [<work_dir_name>]

Field	Options	Description	Requirement
-k	None	Keep. Preserves and rebuilds within an existing work tree instead of overwriting it.	Optional
-p	None	When set, and if the FIM supports partial reconfiguration, a PR template tree is generated at the end of the FIM build. The PR template tree is located in the top of the work directory but is relocatable and uses only relative paths. See $OFS_ROOTDIR/syn/common/scripts generate_pr_release.sh for details.	Optional
-e	None	Run only Quartus analysis and elaboration. It completes the setup stage, passes -end synthesis to the Quartus compilation flow and exits without running the finish stage.	Optional
--stage	all | setup | compile | finish	Controls which portion of the OFS build is run.   - all: Run all build stages (default)   - setup: Initialize a project in the work directory   - compile: Run the Quartus compilation flow on a project that was already initialized with setup   - finish: Complete OFS post-compilation tasks, such as generating flash images and, if -p is set, generating a release.	Optional
--ofss	<ip_config>.ofss | nodefault	OFS Settings. OFSS files are used to modify IP in the design. This parameter is consumed during the setup stage and IP is updated only inside the work tree. More than one .ofss file may be passed to the --ofss switch by concatenating them separated by commas. For example: --ofss config_a.ofss,config_b.ofss. If no OFSS files are provided, the script will default to using the .ofss file to configure the design. You may specify --ofss nodefault to prevent the script from using the default OFSS configuration; the resulting build will only use the source files as-is, plus any OFSS files you specify.	Optional
<build_target>	n6000 | n6001 | fseries-dk | iseries-dk	Specifies which board is being targeted.	Required
<fim_options>	flat | null_he_lb | null_he_hssi | null_he_mem | null_he_mem_tg | no_hssi	Used to change how the FIM is built.   • flat - Compiles a flat design (no PR assignments). This is useful for bringing up the design on a new board without dealing with PR complexity.   • null_he_lb - Replaces the Host Exerciser Loopback (HE_LBK) with he_null.   • null_he_hssi - Replaces the Host Exerciser HSSI (HE_HSSI) with he_null.   • null_he_mem - Replaces the Host Exerciser Memory (HE_MEM) with he_null.   • null_he_mem_tg - Replaces the Host Exerciser Memory Traffic Generator with he_null.   • no_hssi - Removes the HSSI-SS from the FIM. More than one FIM option may be passed included in the <fim_options> list by concatenating them separated by commas. For example: <build_target>:flat,null_he_lb,null_he_hssi	Optional
<work_dir_name>	String	Specifies the name of the work directory in which the FIM will be built. If not specified, the default target is $OFS_ROOTDIR/work	Optional

Refer to Compile OFS FIM which provides step-by-step instructions for running the build_top.sh script with some of the different available options.

2.1.1.1 Build Work Directory

The build script copies source files from the existing cloned repository into the specified work directory, which are then used for compilation. As such, any changes made in the base source files will be included in all subsequent builds, unless the -k option is used, in which case an existing work directories files are used as-is. Likewise, any changes made in a work directory is only applied to that work directory, and will not be updated in the base repository by default. When using OFSS files to modify the design, the build script will create a work directory and make the modifications in the work directory.

2.1.1.2 Null Host Exercisers

When using the he_null_x command command line options, the specified Host Exerciser is replaced by an he_null block. The he_null is a minimal block with CSRs that responds to PCIe MMIO requests in order to keep PCIe alive. You may use any of the build flows (flat, in-tree, out-of-tree) with the HE_NULL compile options. The HE_NULL compile options are as follows:

• null_he_lb - Replaces the Host Exerciser Loopback (HE_LBK) with he_null
• null_he_hssi - Replaces the Host Exerciser HSSI (HE_HSSI) with he_null
• null_he_mem - Replaces the Host Exerciser Memory (HE_MEM) with he_null
• null_he_mem_tg - Replaces the Host Exerciser Memory Traffic Generator with he_null

The Compile OFS FIM section gives step-by-step instructions for this flow.

2.1.2 OFSS File Usage

The OFS FIM build script uses OFSS files to configure the design IP prior to compilation using preset configurations. The OFSS files specify certain parameters for different IPs. Using OFSS is provided as a convenience feature for building different FIM configurations. You can specify the IP OFSS files you wish to use on the command line, by editing the default Platform OFSS file, or by creating a custom Platform OFSS file and calling it on the command line. Any IP OFSS file type not explicitly specified will default to the one defined in the default Platform OFSS file.

The following video describes OFS Settings files, and provides demonstrations showing how to easily customize the OFS reference shell designs and accelerate your development flow.

2.1.2.1 Top Level OFSS File

Top-level OFSS files are OFSS files that contain a list of IP OFSS files that will be used during compilation when the Top-level OFSS file is provided to the build script. You may make your own custom Top-level OFSS files for convenient compilation. The Provided Top-level OFSS Files table describes the Top-level OFSS files that are provided to you.

Top-level OFSS files contain a [default] header, followed by all of the IP OFSS files that will be used by the build script when this Platform OFSS file is called. Ensure that any environment variables (e.g. $OFS_ROOTDIR) are set correctly. The OFSS Config tool uses breadth first search to include all of the specified OFSS files; the ordering of OFSS files does not matter.

The general structure of a Top-level OFSS file is as follows:

[default]
<PATH_TO_BASE_OFSS_FILE>
<PATH_TO_PCIE_OFSS_FILE>
<PATH_TO_IOPLL_OFSS_FILE>
<PATH_TO_MEMORY_OFSS_FILE>
<PATH_TO_HSSI_OFSS_FILE>

Any IP OFSS file types that are not explicitly defined by the user will default to using the IP OFSS files specified in the default Top-level OFSS file of the target board. The default Top-level OFSS file for each target is /tools/ofss_config/<target_board>.ofss. You can use the --ofss nodefault option to prevent the build script from using the default Top-level OFSS file. You can still provide other OFSS files while using the nodefault option, e.g. --ofss nodefault tools/ofss_config/pcie/pcie_host_2link.ofss will implement the settings within pcie_host_2link.ofss, and will not use any default settings for the other IP types.

Table: Provided Top-Level OFSS Files

OFSS File Name	Location	Type	Description	Supported Board
n6001.ofss	$OFS_ROOTDIR/tools/ofss_config	Top-level	This is the default for N6001. Includes the following OFSS files:   • n6001_base.ofss   • pcie_host.ofss   • iopll_500MHz.ofss   • memory.ofss   • hssi_8x25.ofss	N6001
n6000.ofss	$OFS_ROOTDIR/tools/ofss_config	Top-level	This is the default for N6000. Includes the following OFSS files:   • n6000_base.ofss   • pcie_host_n6000.ofss   • iopll_350MHz.ofss   • hssi_4x100.ofss	N6000
fseries-dk.ofss	$OFS_ROOTDIR/tools/ofss_config	Top-level	This is the default for fseries-dk. Includes the following OFSS files:   • fseries-dk_base.ofss   • pcie_host.ofss   • iopll_500MHz.ofss   • memory_ftile.ofss   • hssi_8x25_ftile.ofss	fseries-dk
iseries-dk.ofss	$OFS_ROOTDIR/tools/ofss_config	Top-level	This is the default for iseries-dk. Includes the following OFSS files:   • iseries-dk_base.ofss   • pcie_host.ofss   • iopll_500MHz.ofss   • memory_rtile.ofss   • hssi_8x25_ftile.ofss	iseries-dk

2.1.2.2 Base OFSS File

An OFSS file with IP type ofs contains board specific information for the target board. It defines certain attributes of the design, including the platform name, device family, fim type, part number, and device ID. It can also contain settings for system information like PCIe generation and subsystem device IDs. Note that PCIe settings defined in the PCIe OFSS file will take precedence over any PCIe settings defined in the Base OFSS file.

Currently supported configuration options for an OFSS file with IP type ofs are described in the OFS IP OFSS File Options table.

Table: OFS IP OFSS File Options

Section	Parameter	n6001 Default Value	n6000 Default Value	fseries-dk Default Value	iseries-dk Default Value
[ip]	type	ofs	ofs	ofs	ofs
[settings]	platform	n6001	n6000	n6001	n6001
	family	agilex	agilex	agilex	agilex
	fim	base_x16	base_x16	base_x16	base_x16
	part	AGFB014R24A2E2V	AGFB014R24A2E2V	AGFB027R24C2E2VR2	AGIB027R29A1E2VR3
	device_id	6001	6000	6001	6001
[pcie.settings]	pcie_gen	4	4	4	5
[pcie]	subsys_dev_id	1771	1770	1	1
	exvf_subsysid	1771	1770	1	1

The Provided Base OFSS Files table describes the Base OFSS files that are provided to you.

Table: Provided Base OFSS Files

OFSS File Name	Location	Type	Supported Board
n6001_base.ofss	$OFS_ROOTDIR/tools/ofss_config/base	ofs	N6001
n6000_base.ofss	$OFS_ROOTDIR/tools/ofss_config/base	ofs	N6000
fseries-dk_base.ofss	$OFS_ROOTDIR/tools/ofss_config/base	ofs	fseries-dk
iseries-dk_base.ofss	$OFS_ROOTDIR/tools/ofss_config/base	ofs	iseries-dk

2.1.2.3 PCIe OFSS File

An OFSS file with IP type pcie is used to configure the PCIe-SS and PF/VF MUX in the FIM.

The PCIe OFSS file has a special section type ([pf*]) which is used to define physical functions (PFs) in the FIM. Each PF has a dedicated section, where the * character is replaced with the PF number. For example, [pf0], [pf1], etc. For reference FIM configurations, you must have at least 1 PF with 1VF, or 2PFs. This is because the PR region cannot be left unconnected. PFs must be consecutive. The PFVF Limitations table describes the supported number of PFs and VFs.

Table: PF/VF Limitations

Parameter	Value
Min # of PFs	1 PF if 1 or more VFs present | 2 PFs if 0 VFs present (PFs must start at PF0)
Max # of PFs	8
Min # of VFs	0 VFs if 2 or more PFs present | 1 VF if only 1 PF present
Max # of VFs	2000 distributed across all PFs

Currently supported configuration options for an OFSS file with IP type pcie are described in the PCIe IP OFSS File Options table.

Table: PCIe IP OFSS File Options

Section	Parameter	Options	Description	n6001 Default Value	n6000 Default Value	fseries-dk Default Value	iseries-dk Default Value
[ip]	type	pcie	Specifies that this OFSS file configures the PCIe-SS	pcie	pcie	pcie	pcie
[settings]	output_name	pcie_ss	Specifies the output name of the PCIe-SS IP	pcie_ss	pcie_ss	pcie_ss	pcie_ss
	ip_component	intel_pcie_ss_axi | pcie_ss	Specifies the PCIe SS IP that will be used.   • intel_pcie_ss_axi: AXI Streaming Intel FPGA IP for PCI Express   • pcie_ss: Intel FPGA IP Subsystem for PCI Express	intel_pcie_ss_axi	intel_pcie_ss_axi	intel_pcie_ss_axi	intel_pcie_ss_axi
	preset	String	OPTIONAL - Specifies the name of a PCIe-SS IP presets file to use when building the FIM. When used, a presets file will take priority over any other parameters set in this OFSS file.	N/A	N/A	N/A	N/A
[pf*]	num_vfs	Integer	Specifies the number of Virtual Functions in the current PF	Variable[1]	Variable[2]	Variable[1]	Variable[1]
	bar0_address_width	Integer		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	bar4_address_width	Integer		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	vf_bar0_address_width	Integer		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	ats_cap_enable	0 | 1		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	vf_ats_cap_enable	0 | 1		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	prs_ext_cap_enable	0 | 1		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	pasid_cap_enable	0 | 1		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	pci_type0_vendor_id	32'h Value		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	pci_type0_device_id	32'h Value		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	revision_id	32'h Value		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	class_code	32'h Value		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	subsys_vendor_id	32'h Value		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	subsys_dev_id	32'h Value		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	sriov_vf_device_id	32'h Value		Variable[1]	Variable[2]	Variable[1]	Variable[1]
	exvf_subsysid	32'h Value		Variable[1]	Variable[2]	Variable[1]	Variable[1]

^[1] Refer to pcie_host.ofss

^[2] Refer to pcie_host_n6000.ofss

Any parameter that is not specified in the PCIe OFSS file will default to the values defined in $OFS_ROOTDIR/ofs-common/tools/ofss_config/ip_params/pcie_ss_component_parameters.py. When using a PCIe IP OFSS file during compilation, the PCIe-SS IP that is used will be defined based on the values in the PCIe IP OFSS file plus the parameters defined in pcie_ss_component_parameters.py.

The Provided PCIe OFSS Files table describes the PCIe OFSS files that are provided to you.

Table: Provided PCIe OFSS Files

OFSS File Name	Location	Type	Description	Supported Boards
pcie_host.ofss	$OFS_ROOTDIR/tools/ofss_config/pcie	pcie	Defines the PCIe Subsystem with the following configuration:   • PF0 (3 VFs)   • PF1 (0 VFs)   • PF2 (0 VFs)   • PF3 (0 VFs)   • PF4 (0 VFs)	N6001 | fseries-dk | iseries-dk
pcie_host_1pf_1vf.ofss	$OFS_ROOTDIR/tools/ofss_config/pcie	pcie	Defines the PCIe Subsystem with the following configuration:   • PF0 (1 VF)	N6001 | fseries-dk | iseries-dk
pcie_host_2link.ofss	$OFS_ROOTDIR/tools/ofss_config/pcie	pcie	Defines the PCIe Subsystem with the following configuration:   • 2x8 PCIe   • PF0 (3 VFs)   • PF1 (0 VFs)   • PF2 (0 VFs)   • PF3 (0 VFs)   • PF4 (0 VFs)	iseries-dk
pcie_host_2link_1pf_1vf.ofss	$OFS_ROOTDIR/tools/ofss_config/pcie	pcie	Defines the PCIe Subsystem with the following configuration:   • 2x8 PCIe   • PF0 (1 VF)	iseries-dk
pcie_host_2pf.ofss	$OFS_ROOTDIR/tools/ofss_config/pcie	pcie	Defines the PCIe Subsystem with the following configuration:   • PF0 (0 VFs)   • PF1 (0 VFs)	N6001 | fseries-dk | iseries-dk
pcie_host_gen4.ofss	$OFS_ROOTDIR/tools/ofss_config/pcie	pcie	Defines the PCIe Subsystem with the following configuration:   • PF0 (3 VFs)   • PF1 (0 VFs)   • PF2 (0 VFs)   • PF3 (0 VFs)   • PF4 (0 VFs)	iseries-dk
pcie_host_n6000.ofss	$OFS_ROOTDIR/tools/ofss_config/pcie	pcie	Defines the PCIe Subsystem for the N6000 with the following configuration:   • PF0 (3 VFs)   • PF1 (0 VFs)   • PF2 (0 VFs)   • PF3 (0 VFs)   • PF4 (0 VFs)	N6001

2.1.2.4 IOPLL OFSS File

An OFSS file with IP type iopll is used to configure the IOPLL in the FIM.

The IOPLL OFSS file has a special section type ([p_clk]) which is used to define the IOPLL clock frequency.

Currently supported configuration options for an OFSS file with IP type iopll are described in the IOPLL OFSS File Options table.

Table: IOPLL OFSS File Options

Section	Parameter	Options	Description	n6001 Default Value	n6000 Default Value	fseries-dk Default Value	iseries-dk Default Value
[ip]	type	iopll	Specifies that this OFSS file configures the IOPLL	iopll	iopll	iopll	iopll
[settings]	output_name	sys_pll	Specifies the output name of the IOPLL.	sys_pll	sys_pll	sys_pll	sys_pll
	instance_name	iopll_0	Specifies the instance name of the IOPLL.	iopll_0	iopll_0	iopll_0	iopll_0
[p_clk]	freq	Integer: 250 - 500	Specifies the IOPLL clock frequency in MHz.	500	350	500	500

The Provided IOPLL OFSS Files table describes the IOPLL OFSS files that are provided to you.

Table: Provided IOPLL OFSS Files

OFSS File Name	Location	Type	Description	Supported Board
iopll_500MHz.ofss	$OFS_ROOTDIR/tools/ofss_config/iopll	iopll	Sets the IOPLL frequency to 500 MHz	N6001 | fseries-dk | iseries-dk
iopll_470MHz.ofss	$OFS_ROOTDIR/tools/ofss_config/iopll	iopll	Sets the IOPLL frequency to 470 MHz	N6001 | fseries-dk | iseries-dk
iopll_350MHz.ofss	$OFS_ROOTDIR/tools/ofss_config/iopll	iopll	Sets the IOPLL frequency to 350 MHz	N6001 | N6000 | fseries-dk | iseries-dk

2.1.2.5 Memory OFSS File

An OFSS file with IP type memory is used to configure the Memory-SS in the FIM.

The Memory OFSS file specifies a preset value, which selects a presets file (.qprs) to configure the Memory-SS.

Currently supported configuration options for an OFSS file with IP type memory are described in the Memory OFSS File Options table.

Table: Memory OFSS File Options

Section	Parameter	Options	Description	n6001 Default Value	n6000 Default Value	fseries-dk Default Value	iseries-dk Default Value
[ip]	type	memory	Specifies that this OFSS file configures the Memory-SS	memory	N/A	memory	memory
[settings]	output_name	mem_ss_fm	Specifies the output name of the Memory-SS.	mem_ss_fm	N/A	mem_ss_fm	mem_ss_fm
	preset	String[1]	Specifies the name of the .qprs presets file that will be used to build the Memory-SS.	n6001	N/A	fseries-dk	iseries-dk

^[1] You may generate your own .qprs presets file with a unique name using Quartus.

Memory-SS presets files are stored in the $OFS_ROOTDIR/ipss/mem/qip/presets directory.

The Provided Memory OFSS Files table describes the Memory OFSS files that are provided to you.

Table: Provided Memory OFSS Files

OFSS File Name	Location	Type	Description	Supported Board
memory.ofss	$OFS_ROOTDIR/tools/ofss_config/memory	memory	Defines the memory IP preset file to be used during the build as:	N6001 | N6000 [1]
memory_ftile.ofss	$OFS_ROOTDIR/tools/ofss_config/memory	memory	Defines the memory IP preset file to be used during the build as fseries-dk	fseries-dk
memory_rtile.ofss	$OFS_ROOTDIR/tools/ofss_config/memory	memory	Defines the memory IP preset file to be used during the build as iseries-dk	iseries-dk
memory_rtile_no_dimm.ofss	$OFS_ROOTDIR/tools/ofss_config/memory	memory	Defines the memory IP preset file to be used during the build as iseries-dk	iseries-dk

^[1] The memory.ofss file can be used for the N6000, however, the default N6000 FIM does not implement the Memory Sub-system. Refer to Section 4.7.2 for step-by-step instructions on how to enable the Memory sub-system

2.1.2.6 HSSI IP OFSS File

An OFSS file with IP type hssi is used to configure the Ethernet-SS in the FIM.

Currently supported configuration options for an OFSS file with IP type hssi are described in the HSSI OFSS File Options table.

Table: HSSI OFSS File Options

Section	Parameter	Options	Description	n6001 Default Value	n6000 Default Value	fseries-dk Default Value	iseries-dk Default Value
[ip]	type	hssi	Specifies that this OFSS file configures the Ethernet-SS	hssi	hssi	hssi	hssi
[settings]	output_name	hssi_ss	Specifies the output name of the Ethernet-SS	hssi_ss	hssi_ss	hssi_ss	hssi_ss
	num_channels	Integer	Specifies the number of channels.	8	4	8	8
	data_rate	10GbE | 25GbE | 100GCAUI-4 | 200GAUI-4 | 400GAUI-8	Specifies the data rate[1]	25GbE	100GCAUI-4	25GbE	25GbE
	preset	None | fseries-dk | 200g-fseries-dk | 400g-fseries-dk | String[1]	OPTIONAL - Selects the platform whose preset .qprs file will be used to build the Ethernet-SS. When used, this will overwrite the other settings in this OFSS file.	N/A	N/A	N/A	N/A

^[1] The presets file will take priority over the data_rate parameter, so this value will not take effect if using a presets file.

^[2] You may generate your own .qprs presets file with a unique name using Quartus.

Ethernet-SS presets are stored in $OFS_ROOTDIR/ipss/hssi/qip/hssi_ss/presets directory.

The Provided HSSI OFSS Files table describes the HSSI OFSS files that are provided to you.

Table: Provided HSSI OFSS Files

OFSS File Name	Location	Type	Description	Supported Board
hssi_8x10.ofss	$OFSS_ROOTDIR/tools/ofss_config/hssi	hssi	Defines the Ethernet-SS IP configuration to be 8x10 GbE	N6001
hssi_8x25.ofss	$OFSS_ROOTDIR/tools/ofss_config/hssi	hssi	Defines the Ethernet-SS IP configuration to be 8x25 GbE	N6001
hssi_2x100.ofss	$OFSS_ROOTDIR/tools/ofss_config/hssi	hssi	Defines the Ethernet-SS IP configuration to be 2x100 GbE	N6001
hssi_1x400_ftile.ofss	$OFSS_ROOTDIR/tools/ofss_config/hssi	hssi	Defines the Ethernet-SS IP configuration to be F-Tile 1x400 GbE	iseries-dk
hssi_4x100.ofss	$OFSS_ROOTDIR/tools/ofss_config/hssi	hssi	Defines the Ethernet-SS IP configuration to be 4x100 GbE	N6000
hssi_8x25_ftile.ofss	$OFSS_ROOTDIR/tools/ofss_config/hssi	hssi	Defines the Ethernet-SS IP configuration to be F-Tile 8x25 GbE	fseries-dk | iseries-dk
hssi_2x200_ftile.ofss	$OFSS_ROOTDIR/tools/ofss_config/hssi	hssi	Defines the Ethernet-SS IP to be 2x200 GbE	iseries-dk

2.1.3 OFS Build Script Outputs

The output files resulting from running the the OFS FIM build_top.sh build script are copied to a single directory during the finish stage of the build script. The path for this directory is: $OFS_ROOTDIR/<WORK_DIRECTORY>/syn/board/iseries-dk/syn_top/output_files.

The output files include programmable images and compilation reports. The OFS Build Script Output Descriptions table describes the images that are generated by the build script.

Table: OFS Build Script Output Descriptions

File Name	Description
ofs_top.sof	The FIM design SRAM Object File; a binary file of the compiled FIM image.

2.2 Compilation Flows

This section provides information for using the build script to generate different FIM types. Walkthroughs are provided for each compilation flow. These walkthroughs require that the development environment has been set up as described in the Set Up Development Environment section.

2.2.1 Flat FIM

A flat FIM is compiled such that there is no partial reconfiguration region, and the entire design is built as a flat design. This is useful for compiling new designs without worrying about the complexity introduced by partial reconfiguration. The flat compile removes the PR region and PR IP; thus, you cannot use the -p build flag when using the flat compile setting. Refer to the Compile OFS FIM Section for step-by-step instructions for this flow.

2.2.2 In-Tree PR FIM

An In-Tree PR FIM is the default compilation if no compile flags or compile settings are used. This flow will compile the design with the partial reconfiguration region, but it will not create a relocatable PR directory tree to aid in AFU development. Refer to the Compile OFS FIM Section for step-by-step instructions for this flow.

2.2.3 Out-of-Tree PR FIM

An Out-of-Tree PR FIM will compile the design with the partial reconfiguration region, and will create a relocatable PR directory tree to aid in AFU workload development. This is especially useful if you are developing a FIM to be used by another team developing AFU workloads. This is the recommended build flow in most cases. There are two ways to create the relocatable PR directory tree:

• Run the FIM build script with the -p option. Refer to the Compile OFS FIM Section for step-by-step instructions for this flow.
• Run the generate_pr_release.sh script after running the FIM build script. Refer to the Manually Generate OFS Out-Of-Tree PR FIM Section step-by-step instructions for this flow.

In both cases, the generate_pr_release.sh is run to create the relocatable build tree. This script is located at $OFS_ROOTDIR/ofs-common/scripts/common/syn/generate_pr_release.sh. Usage for this script is as follows:

generate_pr_release.sh -t <PATH_OF_RELOCATABLE_PR_TREE> <BOARD_TARGET> <WORK_DIRECTORY>

The Generate PR Release Script Options table describes the options for the generate_pr_release.sh script.

Table: Generate PR Release Script Options

Parameter	Options	Description
<PATH_OF_RELOCATABLE_PR_TREE>	String	Specifies the location of the relocatable PR directory tree to be created.
<BOARD_TARGET>	iseries-dk	Specifies the name of the board target.
<WORK_DIRECTORY>	String	Specifies the existing work directory from which the relocatable PR directory tree will be created from.

After generating the relocatable build tree, it is located in the $OFS_ROOTDIR/<WORK_DIRECTORY>/pr_build_template directory (or the directory you specified if generated separately). The contents of this directory have the following structure:

├── bin
├── ├── afu_synth
├── ├── qar_gen
├── ├── update_pim
├── ├── run.sh
├── ├── build_env_config
├── README
├── hw
├── ├── lib
├── ├── ├── build
├── ├── ├── fme-ifc-id.txt
├── ├── ├── platform
├── ├── ├── fme-platform-class.txt
├── ├── blue_bits
└── ├── ├── ofs_top.sof

2.2.4 HE_NULL FIM

An HE_NULL FIM refers to a design with one, some, or all of the Host Exercisers replaced by he_null blocks. The he_null is a minimal block with CSRs that responds to PCIe MMIO requests in order to keep PCIe alive. You may use any of the build flows (flat, in-tree, out-of-tree) with the HE_NULL compile options. The HE_NULL compile options are as follows:

• null_he_lb - Replaces the Host Exerciser Loopback (HE_LBK) with he_null
• null_he_hssi - Replaces the Host Exerciser HSSI (HE_HSSI) with he_null
• null_he_mem - Replaces the Host Exerciser Memory (HE_MEM) with he_null
• null_he_mem_tg - Replaces the Host Exerciser Memory Traffic Generator with he_null

The Compile OFS FIM section gives step-by-step instructions for this flow.

2.2.5 Walkthrough: Compile OFS FIM

Perform the following steps to compile the OFS Agilex PCIe Attach FIM for iseries-dk:

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Navigate to the root directory.

   cd $OFS_ROOTDIR
   

4. Run the build_top.sh script with the desired compile options. The following is used build the default iseries-dk design:

   ./ofs-common/scripts/common/syn/build_top.sh iseries-dk work_iseries-dk
   

   The build command options allow for many modifications to the shell design at build time. The following tool is provided to help you conveniently get the build command for a specific shell configuration:

OFS Build Command Generator

Build Flow Options

Build Target

n6001 n6000 fseries-dk iseries-dk

Partial Reconfiguration Settings

Disable Partial Reconfiguration
Generate Relocatable PR Tree

Add/Remove Subsystems

Remove HSSI-SS (Ethernet Sub-System)

Add/Remove Host Exercisers

Remove HE_HSSI (Ethernet Host Exerciser)
Remove HE_LBK (PCIe Loopback)
Remove HE_MEM (Read/Write Memory Exerciser)
Remove HE_MEM_TG (Pseudo random memory traffic generator)

IP Configuration

HSSI

default 8x10 GbE 8x25 GbE 2x100 GbE 2x200 GbE 1x400 GbE

IOPLL

default 500 MHz 470 MHz 350 MHz

PCIe

default 1x16 5PF/3VF 1x16 1PF/1VF 1x16 2PF/0VF 2x8 3PF/3VF 2x8 1PF/1VF
Gen4 Gen5

Press submit to generate the build command.

Note: If no OFSS file is specified, the build script will use the <target>.ofss file by default.

1. Once the build script is complete, the build summary should report that the build is complete and passes timing. For example:

   ***********************************
   ***
   ***        OFS_PROJECT: ofs-agx7-pcie-attach
   ***        OFS_BOARD: iseries-dk
   ***        Q_PROJECT:  ofs_top
   ***        Q_REVISION: ofs_top
   ***        SEED: 1
   ***        Build Complete
   ***        Timing Passed!
   ***
   ***********************************
   

2.2.6 Walkthrough: Manually Generate OFS Out-Of-Tree PR FIM

This walkthrough describes how to manually generate an Out-Of-Tree PR FIM. This can be automatically done for you if you run the build script with the -p option. This process is not applicable if you run the build script with the flat option.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Navigate to the root directory.

   cd $OFS_ROOTDIR
   

4. Run the build_top.sh script with the desired compile options using the iseries-dk OFSS presets. In order to create the relocatable PR tree, you may not compile with the flat option. For example:

   ./ofs-common/scripts/common/syn/build_top.sh iseries-dk work_iseries-dk
   

5. Run the generate_pr_release.sh script to create the relocatable PR tree.

   ./ofs-common/scripts/common/syn/generate_pr_release.sh -t work_iseries-dk/pr_build_template iseries-dk work_iseries-dk
   

2.2.7 Compilation Seed

You may change the seed which is used by the build script during Quartus compilation to change the starting point of the fitter. Trying different seeds is useful when your design is failing timing by a small amount.

2.2.7.1 Walkthrough: Change the Compilation Seed

Perform the following steps to change the compilation seed for the FIM build.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Edit the SEED assignment in the $OFS_ROOTDIR/syn/board/iseries-dk/syn_top/ofs_top.qsf file to your desired seed value. The value can be any non-negative integer value.

   set_global_assignment -name SEED 2
   

4. Build the FIM. Refer to the Compile OFS FIM section for instructions.

3. FIM Simulation

Unit level simulation of key components in the FIM is provided for verification of the following areas:

• Ethernet
• PCIe
• External Memory
• Core FIM

The Unit Level simulations work with Synopsys VCS/VCSMX or Mentor Graphics Questasim simulators. The scripts to run each unit level simulation are located in $OFS_ROOTDIR/sim/unit_test. Each unit test directory contains a README which describes the test in detail.

Refer to the Supported Unit Tests table for a list of the supported unit tests.

Table: Supported Unit Tests

Test Name	Description	n6001	n6000	fseries-dk	iseries-dk
bfm_test	This is the unit test for PCIe BFM. The test uses HE-LB to perform memory loopback between FIM and the host.	✓	✓	✓	✓
csr_test	This is the unit test for FIM CSR access and AFU memory write/read The Verilog macro 'SIM_USE_PCIE_DUMMY_CSR' is enabled to switch to a dummy CSR instance in pcie_top. The dummy CSR implements full RW registers which is useful to test MMIO write/read burst to FIM CSR region. It covers the following test scenarios:   • MMIO write 32-bit address and 64-bit address (FIM and AFU)   • MMIO read 32-bit address and 64-bit address (FIM and AFU)   • Simple memory loopback test using he_lb - this is similar to simple_test_pcie except that it uses a simple pcie BFM	✓	✓	✓	✓
dfh_walker	This is the unit test for FME DFH walking	✓	✓	✓	✓
flr	This is the unit test for PCIe PF/VF FLR. It covers the following test scenarios:   • PF FLR request and response   • VF FLR request and response	✓	✓	✓	✓
fme_csr_access	This is the a unit test for the register access logic for $OFS_ROOTDIR/ofs-common/src/common/fme/fme_csr.sv It covers the following test scenarios:   • Ensures CSR registers do not have any unknown "x" bits.   • Checks that CSR register read accesses to not return with any unknown "x" bits.   • Returning read and write AXI responses to CSR register addresses are checked to make sure all return with "RESP_OKAY".   • Checks that all register access types operate correctly:       • Lower 32-bit read/writes.       • Upper 32-bit read/writes.       • Full 64-bit read/writes.   • Checks all non-CSR reads return with all zeros.	✓	✓	✓	✓
fme_csr_directed	This is the unit test for $OFS_ROOTDIR/ofs-common/src/common/fme/fme_csr.sv It covers the following test scenarios:   • MMIO reads to FME registers.   • MMIO writes to FME registers.   • Test of Register bit attributes.   • Test of update/status values read from FME inputs through FME registers.   • Test of update/control values written to FME registers and driven on FME outputs.   • Test of reads/writes outside of valid register range in valid FME Ranges.	✓	✓	✓	✓
he_lb_test	This is the unit test for HE_LPBK. The test uses HE-LB to perform memory loopback between FIM and the host.	✓	✓	✓	✓
he_mem_lb_test	This is the unit test for HE_LPBK. The test uses HE-LB to perform memory loopback between FIM and the host.	✓	✓	✓	✓
he_null_test	This is the unit test for HE-NULL Exerciser. The test issues basic mmio Rd/Wr requests targetting HE-NULL CSRs.	✓	✓	✓	✓
hssi_csr_test	This is the unit test for HE_HSSI/HSSI SS CSR access test	✓	✓	✓	✓
hssi_kpi_test	This is the unit test for HE_HSSI/HSSI SS CSR access and HSSI traffic test. It covers the following test scenarios:   • MMIO write 32-bit address and 64-bit address   • Simple ethernet traffic loopback test using HE_HSSI	✓	✓	✓	✓
hssi_test	This is the unit test for HE_HSSI/HSSI SS CSR access and HSSI traffic test. It covers the following test scenarios:   • MMIO write 32-bit address and 64-bit address   • Simple ethernet traffic loopback test using HE_HSSI	✓	✓	✓	✓
indirect_csr	This is the unit test for axi4lite_indirect_csr_if module. It covers the following test scenarios:   • Indirect CSR write   • Indirect CSR read	✓	✓	✓	✓
mem_ss_csr_test	This is the unit test for the Mem SS CSRs. It checks the contents of the EMIF DFH and MemSS CSRs and compares them to the expected startup configuration.	✓	✓	✓	✓
mem_ss_rst_test	This is the unit test for the Mem SS reset sequence. It enables the reset port on the Mem SS so that a reset is performed after EMIF initialization/calibration.	✓	✓	✓	✓
mem_tg_test	This is the unit test for HE-MEM Traffic generators. The test exercises MMIO access to the HE-MEM TG AFU at PF2 VF2 and runs the traffic generators to test the memory interface.	✓	✓	✓	✓
pcie_ats_basic_test	This is a basic test of PCIe ATS messages and ATS invalidation handling. PCIe ATS must be enabled in the FIM Quartus project being simulated. If ATS is not enabled the test will pass but do nothing. The FIM has an ATS invalidation handler that generates responses for AFUs that are not holding address translations. The test begins by sending an inval to each AFU in the port gasket and confirms that the FIM responds. It then requests ATS translations on each port and confirms they are successful. After that, more ATS invalidations are sent and the test confirms that the AFUs see them and respond -- not the FIM.	✓	✓	✓	✓
pcie_csr_test	This is the unit test for PCIE CSR access. It covers the following test scenarios:   • MMIO access 32-bit address and 64-bit address to PCIe CSR   • MMIO access 32-bit address and 64-bit address to unused PCIe CSR region	✓	✓	✓	✓
pf_vf_access_test	This is the unit test for PCIe PF/VF MMIO. Each function has a feature GUID at offset 0x8 with an associated register map. For testing CSR access we only exercise a single 64b scratchpad who's offset is determined from the GUID. It covers the following test scenarios:   • PF MMIO request and response   • VF MMIO request and response	✓	✓	✓	✓
pmci_csr_test	This is the unit test for PMCI CSR access. It covers the following test scenarios:   • MMIO access 32-bit address and 64-bit address to PMCI CSR   • MMIO access 32-bit address and 64-bit address to unused PMCI CSR region	✓	✓
pmci_mailbox_test	This is the unit test for PMCI M10 accessible registers and RW mailbox registers. It covers the following test scenarios:   • Accessing PMCI RW mailbox register through SPI loopback	✓	✓
pmci_rd_default_value_test	This is the unit test for PMCI Flash Write Read access. It covers the following test scenarios:   • PMCI Flash Write Read   • accessing PMCI mailbox register through SPI loopback	✓	✓
pmci_ro_mailbox_test	This is the unit test for PMCI RO mailbox registers. It covers the following test scenarios:   • accessing PMCI RO mailbox register through SPI loopback	✓	✓
pmci_vdm_b2b_drop_err_scenario_test	This is the unit test for error testing of MCTP Back to back Drop scenario. It covers the following test scenarios:   • RX payload will be sent back to back immediately to test this condition.   • PMCI_SS requires some time to process the previous packets before sending this packet since this criteria is not met it will drop the present packet.	✓	✓
pmci_vdm_len_err_scenario_test	This is the unit test for Error scenario testing of MCTP VDM packets. It covers the following test scenarios:   • Error scenario related to length is tested in this testcase. Scenarios include packet length greater than MCTP_BASELINE_MTU, packet length equal to 0.	✓	✓
pmci_vdm_mctp_mmio_b2b_test	This is the unit test for MCTP VDM packets and CSR transactions sent back to back. It covers the following test scenarios:   • MCTP RX transactions are done b2b with CSR transactions.	✓	✓
pmci_vdm_multipkt_error_scenario_test	This is the unit test for multipacket error scenarios in case of MCTP VDM messages. It covers the following test scenarios:   • This testcase covers error scenarios for MCTP VDM multipackets.   • Various scenarios include     • Multipacket with NO EOM     • Multipacket with NO SOM     • Singlepacket with NO SOM     • Multipacket with Middle packet having greater length than the first packet     • Multipacket with Last packet having greater lenght than previous packets.	✓	✓
pmci_vdm_multipkt_tlp_err_test	This is the unit test for checking Error scnearios in multipacket MCTP VDM packets. It covers the following test scenarios:   • This test covers certain error scenarios for multipacket VDM messages   • Error scenarios include:     • Multipackets with different deid,seid,tag,pkt_sequence number etc	✓	✓
pmci_vdm_tlp_error_scenario_test	This is the unit test for covering certain tlp error for single MCTP VDM packets. It covers the following test scenarios:   • Error scenarios include invalid tlp fields for DW0,DW1,DW3 like invalid t9,t8,tc,at,ep,attr,MCTP header version ,tag fields,invalid DEID	✓	✓
pmci_vdm_tx_rx_all_random_lpbk_test	This testcase is written just to cover certain fields like randomizing seid,msg_tag,target_id etc. It is functionally equivalent to pmci_vdm_tx_rx_lpbk_test.	✓	✓
pmci_vdm_tx_rx_all_toggle_test	This testcase is added for improving coverage for MCTP VDM packets TX/RX flow. Functionally same as pmci_vdm_tx_rx_lpbk_test.	✓	✓
pmci_vdm_tx_rx_lpbk_test	This is the unit test for MCTP VDM packets TX/RX flow It covers the following test scenarios:   • BMC component ( inside Testbench) will intiate a MCTP txn with 16DW in TX path.   • This MCTP VDM packets will be formed in PMCI_SS and will be sent to PCIe top (through mctp_tx_bridge).   • These transaction will be looped back at PCIe top (PCIe BFM) and will be sent back in the RX path.   • RX and TX payload comparison is done at BMC side.   • BMC->PMCI->PCIe->PMCI->BMC ( flow of packets).	✓	✓
port_gasket_test	This is the unit test for pg_csr block and it's connectivity to fabric. The test issues mmio Rd/Wr requests targetting the csrs in port_gasket. This test does not do any functional testing of partial reconfiguration, user clock or remote stp.	✓	✓	✓	✓
qsfp_test	This is the unit test for QSFP contrtoller CSR access. It covers the following test scenarios:   • MMIO read-write to common csr with 64-bit address	✓	✓	✓	✓
remote_stp_test	This is the unit test for remote stp. It covers mmio read access to remote_stp registers.	✓	✓	✓	✓
uart_csr	This is the unit test for UART CSR accesses.	✓	✓	✓	✓

3.1 Simulation File Generation

The simulation files must be generated prior to running unit level simulations. The script to generate simulation files is in the following location:

$OFS_ROOTDIR/ofs-common/scripts/common/sim/gen_sim_files.sh

The usage of the gen_sim_files.sh script is as follows:

gen_sim_files.sh [--ofss=<ip_config>] <build_target>[:<fim_options>] [<device>] [<family>]

The Gen Sim Files Script Options table describes the options for the gen_sim_files.sh script.

Table: Gen Sim Files Script Options

Field	Options	Description	Requirement
--ofss	<ip_config>	OFS Settings. OFSS files are used to modify IP in the design. More than one .ofss file may be passed to the --ofss switch by concatenating them separated by commas. For example: --ofss config_a.ofss,config_b.ofss. If no OFSS files are provided, the script will default to using the .ofss file to configure the design. You may specify --ofss nodefault to prevent the script from using the default OFSS configuration; the resulting build will only use the source files as-is, plus any OFSS files you specify.	Optional
<build_target>	iseries-dk	Specifies which board is being targeted.	Required
<fim_options>	null_he_lb | null_he_hssi | null_he_mem | null_he_mem_tg	Used to change how the FIM is built.   - null_he_lb - Replaces the Host Exerciser Loopback (HE_LBK) with he_null.   - null_he_hssi - Replaces the Host Exerciser HSSI (HE_HSSI) with he_null.   - null_he_mem - Replaces the Host Exerciser Memory (HE_MEM) with he_null.   - null_he_mem_tg - Replaces the Host Exerciser Memory Traffic Generator with he_null. More than one FIM option may be passed included in the <fim_options> list by concatenating them separated by commas. For example: <build_target>:null_he_lb,null_he_hssi	Optional
<device>	string	Specifies the device ID for the target FPGA. If not specified, the default device is parsed from the QSF file for the project.	Optional
<family>	string	Specifies the family for the target FPGA. If not specified, the default family is parsed from the QSF file for the project.	Optional

Refer to the Running Individual Unit Level Simulation section for an example of the simulation files generation flow.

When running regression tests, you may use the -g command line argument to generate simulation files automatically; refer to the [Run Regression Unit Level Simulation] section for step-by-step instructions.

3.2 Individual Unit Tests

Each unit test may be run individually using the run_sim.sh script located in the following directory:

$OFS_ROOTDIR/ofs-common/scripts/common/sim/run_sim.sh

The usage for the run_sim.sh script is as follows:

sh run_sim.sh TEST=<test> [VCSMX=<0|1> | MSIM=<0|1>]

The Run Sim Script Options table describes the options for the run_sim.sh script.

Table: Run Sim Script Options

Field	Options	Description
TEST	String	Specify the name of the test to run, e.g. dfh_walker
VCSMX	0 | 1	When set, the VCSMX simulator will be used
MSIM	0 | 1	When set, the QuestaSim simulator will be used

Note: The default simulator is VCS if neither VCSMX nor MSIM are set.

The log for a unit test is stored in a transcript file in the simulation directory of the test that was run.

$OFS_ROOTDIR/sim/unit_test/<TEST_NAME>/<SIMULATOR>/transcript

For example, the log for the DFH walker test using VCSMX would be found at:

$OFS_ROOTDIR/sim/unit_test/dfh_walker/sim_vcsmx/transcript

The simulation waveform database is saved as vcdplus.vpd for post simulation review.

3.2.1 Walkthrough: Running Individual Unit Level Simulation

Perform the following steps to run an individual unit test.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

Steps:

1. Clone the FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Navigate to the simulation directory.

   cd $OFS_ROOTDIR/ofs-common/scripts/common/sim
   

4. Generate the simulation files for the iseries-dk

   ./gen_sim_files.sh iseries-dk
   

5. Navigate to the common simulation directory

   cd $OFS_ROOTDIR/ofs-common/scripts/common/sim
   

6. Run the desired unit test using your desired simulator

   • Using VCS

     sh run_sim.sh TEST=<test_name>
     

   • Using VCSMX

     sh run_sim.sh TEST=<test_name> VCSMX=1
     

   • Using QuestaSim

     sh run_sim.sh TEST=<test_name> MSIM=1
     

   • For example, to run the DFH walker test using VCSMX:

     sh run_sim.sh TEST=dfh_walker VCSMX=1
     

7. Once the test is complete, check the output for the simulation results. Review the log for detailed test results.

   Test status: OK
   
   ********************
     Test summary
   ********************
      test_dfh_walking (id=0) - pass
   Test passed!
   Assertion count: 0
   $finish called from file "/home/ofs-agx7-pcie-attach/sim/unit_test/scripts/../../bfm/rp_bfm_simple/tester.sv", line 210.
   $finish at simulation time         356233750000
              V C S   S i m u l a t i o n   R e p o r t
   Time: 356233750000 fs
   CPU Time:     57.730 seconds;       Data structure size:  47.2Mb
   Tue Sep  5 09:44:19 2023
   run_sim.sh: USER_DEFINED_SIM_OPTIONS +vcs -l ./transcript
   run_sim.sh: run_sim.sh DONE!
   

3.3 Regression Unit Tests

You may use the regression script regress_run.py to run some or all of the unit tests available with a single command. The regression script is in the following location:

$OFS_ROOTDIR/sim/unit_test/scripts/regress_run.py

The usage of the regression script is as follows:

regress_run.py [-h] [-l] [-n <num_procs>] [-k <test_package>] [-s <simulator>] [-g] [--ofss <ip_config>] [-b <board_name>] [-e]

The Regression Unit Test Script Options table describes the options for the regress_run.py script.

Table: Regression Unit Test Script Options

Field	Options	Description
-h | --help	N/A	Show the help message and exit
-l | --local	N/A	Run regression locally
-n | --n_procs	Integer	Maximum number of processes/tests to run in parallel when run locally. This has no effect on farm runs.
-k | --pack	all | fme | he | hssi | list | mem | pmci	Test package to run during regression. The "list" option will look for a text file named "list.txt" in the "unit_test" directory for a text list of tests to run (top directory names). The default test package is all.
-s | --sim	vcs | vcsmx | msim	Specifies the simulator used for the regression tests. The default simulator is vcs
-g | --gen_sim_files	N/A	Generate simulation files. This only needs to be done once per repo update. This is the equivalent of running the gen_sim_files.sh script.
-o | --ofss	<ip_config>.ofss | nodefault	OFS Settings. OFSS files are used to modify IP in the design. More than one .ofss file may be passed to the --ofss switch by concatenating them separated by commas. For example: --ofss config_a.ofss,config_b.ofss. If no OFSS files are provided, the script will default to using the .ofss file to configure the design. You may specify --ofss nodefault to prevent the script from using the default OFSS configuration; the resulting build will only use the source files as-is, plus any OFSS files you specify.
-b | --board_name	iseries-dk	Specifies the board target
-e | --email_list	String	Specifies email list to send results to multiple recipients

The log for each unit test that is run by the regression script is stored in a transcript file in the simulation directory of the test that was run.

$OFS_ROOTDIR/sim/unit_test/<TEST_NAME>/<SIMULATOR>/transcript

For example, the log for the DFH walker test using VCSMX would be found at:

$OFS_ROOTDIR/sim/unit_test/dfh_walker/sim_vcsmx/transcript

The simulation waveform database is saved as vcdplus.vpd for post simulation review.

3.3.1 Walkthrough: Running Regression Unit Level Simulation

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Create a test list file to only run the unit level simulations that are supported for the iseries-dk FIM.

   touch $OFS_ROOTDIR/sim/unit_test/list.txt
   

   Copy the following list into the new file. You may remove tests from this list as desired.

   ./bfm_test/set_params.sh
   ./csr_test/set_params.sh
   ./dfh_walker/set_params.sh
   ./flr/set_params.sh
   ./fme_csr_access/set_params.sh
   ./fme_csr_directed/set_params.sh
   ./he_lb_test/set_params.sh
   ./he_mem_lb_test/set_params.sh
   ./he_null_test/set_params.sh
   ./hssi_csr_test/set_params.sh
   ./hssi_kpi_test/set_params.sh
   ./hssi_test/set_params.sh
   ./indirect_csr/set_params.sh
   ./mem_ss_csr_test/set_params.sh
   ./mem_ss_rst_test/set_params.sh
   ./mem_tg_test/set_params.sh
   ./pcie_ats_basic_test/set_params.sh
   ./pcie_csr_test/set_params.sh
   ./pcie_ss_axis_components/set_params.sh
   ./pf_vf_access_test/set_params.sh
   ./port_gasket_test/set_params.sh
   ./qsfp_test/set_params.sh
   ./remote_stp_test/set_params.sh
   ./uart_csr/set_params.sh
   

4. Navigate to the unit test scripts directory.

   cd $OFS_ROOTDIR/sim/unit_test/scripts
   

5. Run regression test with the your desired options. For example, to simulate with the options to generate simulation files, run locally, use 8 processes, run the specified test list, use VCS simulator, and target the iseries-dk:

   python regress_run.py -g -l -n 8 -k list -s vcs -b iseries-dk
   

   Note: You may run all available tests by using -k all instead of creating and using -k list, however not all tests are supported depending on the target board.

6. Once all tests are complete, check that the tests have passed.

   Passing Unit Tests:24/24 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
      bfm_test:............... PASS -- Time Elapsed:0:01:14.600452
      csr_test:............... PASS -- Time Elapsed:0:01:30.972054
      dfh_walker:............. PASS -- Time Elapsed:0:01:15.179127
      flr:.................... PASS -- Time Elapsed:0:01:14.579890
      fme_csr_access:......... PASS -- Time Elapsed:0:00:48.545993
      fme_csr_directed:....... PASS -- Time Elapsed:0:00:54.702789
      he_lb_test:............. PASS -- Time Elapsed:0:02:11.371956
      he_mem_lb_test:......... PASS -- Time Elapsed:0:41:32.226191
      he_null_test:........... PASS -- Time Elapsed:0:01:11.791063
      hssi_csr_test:.......... PASS -- Time Elapsed:0:44:10.611323
      hssi_kpi_test:.......... PASS -- Time Elapsed:2:28:24.465424
      hssi_test:.............. PASS -- Time Elapsed:2:23:52.603328
      indirect_csr:........... PASS -- Time Elapsed:0:01:02.535460
      mem_ss_csr_test:........ PASS -- Time Elapsed:0:23:37.683859
      mem_ss_rst_test:........ PASS -- Time Elapsed:0:45:19.603426
      mem_tg_test:............ PASS -- Time Elapsed:0:28:59.823955
      pcie_ats_basic_test:.... PASS -- Time Elapsed:0:01:10.104139
      pcie_csr_test:.......... PASS -- Time Elapsed:0:01:10.891950
      pcie_ss_axis_components: PASS -- Time Elapsed:0:02:04.448343
      pf_vf_access_test:...... PASS -- Time Elapsed:0:01:09.465886
      port_gasket_test:....... PASS -- Time Elapsed:0:01:11.912088
      qsfp_test:.............. PASS -- Time Elapsed:0:05:10.887379
      remote_stp_test:........ PASS -- Time Elapsed:0:01:14.684407
      uart_csr:............... PASS -- Time Elapsed:0:01:34.763679
   Failing Unit Tests: 0/24 >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
   >>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>>
         Number of Unit test results captured: 24
         Number of Unit test results passing.: 24
         Number of Unit test results failing.:  0
   

4. FIM Customization

This section describes how to perform specific customizations of the FIM, and provides step-by-step walkthroughs for these customizations. Each walkthrough can be done independently. These walkthroughs require a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment. The FIM Customization Walkthroughs table lists the walkthroughs that are provided in this section. Some walkthroughs include steps for testing on hardware. Testing on hardware requires that you have a deployment environment set up. Refer to the Getting Started Guide: OFS for Agilex® 7 PCIe Attach FPGAs (I-Series Development Kit (2xR-Tile, 1xF-Tile)) for instructions on setting up a deployment environment.

Table: FIM Customization Walkthroughs

Customization Walkthrough Name
Add a new module to the OFS FIM
Modify and run unit tests for a FIM that has a new module
Hardware test a FIM that has a new module
Debug the FIM with Signal Tap
Compile the FIM in preparation for designing your AFU
Resize the Partial Reconfiguration Region
Modify the PCIe Sub-System and PF/VF MUX Configuration Using OFSS
Modify PCIe Configuration Using IP Presets
Migrate to a Different Agilex Device Number
Modify the Ethernet Sub-System to 1x400GbE

4.1 Adding a new module to the FIM

This section provides a information for adding a custom module to the FIM, simulating the new design, compiling the new design, implementing and testing the new design on hardware, and debugging the new design on hardware.

4.1.1 Hello FIM Theory of Operation

If you intend to add a new module to the FIM area, then you will need to inform the host software of the new module. The FIM exposes its functionalities to host software through a set of CSR registers that are mapped to an MMIO region (Memory Mapped IO). This set of CSR registers and their operation is described in FIM MMIO Regions.

See FPGA Device Feature List (DFL) Framework Overview for a description of the software process to read and process the linked list of Device Feature Header (DFH) CSRs within a FPGA.

This example will add a hello_fim module to the design. The Hello FIM example adds a simple DFH register and 64bit scratchpad register connected to the Board Peripheral Fabric (BPF) that can be accessed by the Host. You can use this example as the basis for adding a new feature to your FIM.

For the purposes of this example, the hello_fim module instantiation sets the DFH feature ID (FEAT_ID) to 0x100 which is not currently defined. Using an undefined feature ID will result in no driver being used. Normally, a defined feature ID will be used to associate a specific driver with the FPGA module. Refer to the Device Feature List Feature IDs for a list of DFL feature types and IDs. If you are adding a new module to your design, make sure the Type/ID pair does not conflict with existing Type/ID pairs. You may reserve Type/ID pairs by submitting a pull request at the link above.

The Hello FIM design can be verified by Unit Level simulation, Universal Verification Methodology (UVM) simulation, and running in hardware on the iseries-dk card. The process for these are described in this section.

4.1.1.1 Hello FIM Board Peripheral Fabric (BPF)

The Hello FIM module will be connected to the Board Peripheral Fabric (BPF), and will be connected such that it can be mastered by the Host. The BPF is an interconnect generated by Platform Designer. The Hello FIM BPF Interface Diagram figure shows the APF/BPF Master/Slave interactions, as well as the added Hello FIM module.

Figure: Hello FIM BPF Interface Diagram

The BPF fabric is defined in $OFS_ROOTDIR/src/pd_qsys/fabric/bpf.txt.

We will add the Hello FIM module to an un-used address space in the MMIO region. The Hello FIM MMIO Address Layout table below shows the MMIO region for the Host with the Hello FIM module added at base address 0x16000.

Table: Hello FIM MMIO Address Layout

Offset	Feature CSR set
0x00000	FME AFU
0x10000	PCIe Interface
0x12000	QSFP Controller 0
0x13000	QSFP Controller 1
0x14000	HSSI Interface
0x15000	EMIF Interface
0x16000	Hello FIM

4.1.1.2 Hello FIM CSR

The Hello FIM CSR will consist of the three registers shown in the Hello FIM CSR table below. The DFH and Hello FIM ID registers are read-only. The Scratchpad register supports read and write accesses.

Table: Hello FIM CSR

Offset	Attribute	Description	Default Value
0x016000	RO	DFH(Device Feature Headers) register	0x30000006a0000100
0x016030	RW	Scrachpad register	0x0
0x016038	RO	Hello FIM ID register	0x6626070150000034

4.1.2 Walkthrough: Add a new module to the OFS FIM

Perform the following steps to add a new module to the OFS FIM that can be accessed by the Host.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

Steps:

1. Clone the FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Make hello_fim source directory

   mkdir $OFS_ROOTDIR/src/hello_fim
   

4. Create hello_fim_top.sv file.

   touch $OFS_ROOTDIR/src/hello_fim/hello_fim_top.sv
   

   Copy the following code into hello_fim_top.sv:

   // ***************************************************************************
   //                               INTEL CONFIDENTIAL
   //
   //        Copyright (C) 2023 Intel Corporation All Rights Reserved.
   //
   // The source code contained or described herein and all  documents related to
   // the  source  code  ("Material")  are  owned  by  Intel  Corporation  or its
   // suppliers  or  licensors.    Title  to  the  Material  remains  with  Intel
   // Corporation or  its suppliers  and licensors.  The Material  contains trade
   // secrets  and  proprietary  and  confidential  information  of  Intel or its
   // suppliers and licensors.  The Material is protected  by worldwide copyright
   // and trade secret laws and treaty provisions. No part of the Material may be
   // used,   copied,   reproduced,   modified,   published,   uploaded,  posted,
   // transmitted,  distributed,  or  disclosed  in any way without Intel's prior
   // express written permission.
   //
   // No license under any patent,  copyright, trade secret or other intellectual
   // property  right  is  granted  to  or  conferred  upon  you by disclosure or
   // delivery  of  the  Materials, either expressly, by implication, inducement,
   // estoppel or otherwise.  Any license under such intellectual property rights
   // must be express and approved by Intel in writing.
   //
   // You will not, and will not allow any third party to modify, adapt, enhance, 
   // disassemble, decompile, reverse engineer, change or create derivative works 
   // from the Software except and only to the extent as specifically required by 
   // mandatory applicable laws or any applicable third party license terms 
   // accompanying the Software.
   //
   // -----------------------------------------------------------------------------
   // Engineer     : 
   // Create Date  : September 2023
   // Module Name  : hello_fim_top.sv
   // Project      : OFS
   // -----------------------------------------------------------------------------
   //
   // Description: 
   // This is a simple module that implements DFH registers and 
   // AVMM address decoding logic.
   
   module hello_fim_top  #(
      parameter ADDR_WIDTH  = 12, 
      parameter DATA_WIDTH = 64, 
      parameter bit [11:0] FEAT_ID = 12'h100,
      parameter bit [3:0]  FEAT_VER = 4'h0,
      parameter bit [23:0] NEXT_DFH_OFFSET = 24'h1000,
      parameter bit END_OF_LIST = 1'b0
   )(
      input  logic    clk,
      input  logic    reset,
   // -----------------------------------------------------------
   //  AXI4LITE Interface
   // -----------------------------------------------------------
      ofs_fim_axi_lite_if.slave   csr_lite_if
   );
   
   import ofs_fim_cfg_pkg::*;
   import ofs_csr_pkg::*;
   
   //-------------------------------------
   // Signals
   //-------------------------------------
      logic [ADDR_WIDTH-1:0]              csr_waddr;
      logic [DATA_WIDTH-1:0]              csr_wdata;
      logic [DATA_WIDTH/8-1:0]            csr_wstrb;
      logic                               csr_write;
      logic                               csr_slv_wready;
      csr_access_type_t                   csr_write_type;
   
      logic [ADDR_WIDTH-1:0]              csr_raddr;
      logic                               csr_read;
      logic                               csr_read_32b;
      logic [DATA_WIDTH-1:0]              csr_readdata;
      logic                               csr_readdata_valid;
      logic [ADDR_WIDTH-1:0]              csr_addr;
   
      logic [63:0]                        com_csr_writedata;
      logic                               com_csr_read;
      logic                               com_csr_write;
      logic [63:0]                        com_csr_readdata;
      logic                               com_csr_readdatavalid;
      logic [5:0]                         com_csr_address;
   
   // AXI-M CSR interfaces
   ofs_fim_axi_mmio_if #(
      .AWID_WIDTH   (ofs_fim_cfg_pkg::MMIO_TID_WIDTH),
      .AWADDR_WIDTH (ADDR_WIDTH),
      .WDATA_WIDTH  (ofs_fim_cfg_pkg::MMIO_DATA_WIDTH),
      .ARID_WIDTH   (ofs_fim_cfg_pkg::MMIO_TID_WIDTH),
      .ARADDR_WIDTH (ADDR_WIDTH),
      .RDATA_WIDTH  (ofs_fim_cfg_pkg::MMIO_DATA_WIDTH)
   ) csr_if();
   
   // AXI4-lite to AXI-M adapter
   axi_lite2mmio axi_lite2mmio (
      .clk       (clk),
      .rst_n     (~reset),
      .lite_if   (csr_lite_if),
      .mmio_if   (csr_if)
   );
   
   //---------------------------------
   // Map AXI write/read request to CSR write/read,
   // and send the write/read response back
   //---------------------------------
   ofs_fim_axi_csr_slave #(
      .ADDR_WIDTH (ADDR_WIDTH),
      .USE_SLV_READY (1'b1)
   
      ) csr_slave (
      .csr_if             (csr_if),
   
      .csr_write          (csr_write),
      .csr_waddr          (csr_waddr),
      .csr_write_type     (csr_write_type),
      .csr_wdata          (csr_wdata),
      .csr_wstrb          (csr_wstrb),
      .csr_slv_wready     (csr_slv_wready),
      .csr_read           (csr_read),
      .csr_raddr          (csr_raddr),
      .csr_read_32b       (csr_read_32b),
      .csr_readdata       (csr_readdata),
      .csr_readdata_valid (csr_readdata_valid)
   );
   
   // Address mapping
   assign csr_addr             = csr_write ? csr_waddr : csr_raddr;
   assign com_csr_address      = csr_addr[5:0];  // byte address
   assign csr_slv_wready       = 1'b1 ;
   // Write data mapping
   assign com_csr_writedata    = csr_wdata;
   
   // Read-Write mapping
   always_comb
   begin
      com_csr_read             = 1'b0;
      com_csr_write            = 1'b0;
      casez (csr_addr[11:6])
         6'h00 : begin // Common CSR
            com_csr_read       = csr_read;
            com_csr_write      = csr_write;
         end   
         default: begin
            com_csr_read       = 1'b0;
            com_csr_write      = 1'b0;
         end
      endcase
   end
   
   // Read data mapping
   always_comb begin
      if (com_csr_readdatavalid) begin
         csr_readdata       = com_csr_readdata;
         csr_readdata_valid = 1'b1;
      end
      else begin
         csr_readdata       = '0;
         csr_readdata_valid = 1'b0;
      end
   end
   
   hello_fim_com  #(
      .FEAT_ID          (FEAT_ID),
      .FEAT_VER         (FEAT_VER),
      .NEXT_DFH_OFFSET  (NEXT_DFH_OFFSET),
      .END_OF_LIST      (END_OF_LIST)
   ) hello_fim_com_inst (
      .clk                   (clk                     ),
      .reset                 (reset                   ),
      .writedata             (com_csr_writedata       ),
      .read                  (com_csr_read            ),
      .write                 (com_csr_write           ),
      .byteenable            (4'hF                    ),
      .readdata              (com_csr_readdata        ),
      .readdatavalid         (com_csr_readdatavalid   ),
      .address               (com_csr_address         )
      );
   endmodule
   

5. Create hello_fim_com.sv file.

   touch $OFS_ROOTDIR/src/hello_fim/hello_fim_com.sv
   

   Copy the following code to hello_fim_com.sv:

   module hello_fim_com #(
     parameter bit [11:0] FEAT_ID = 12'h100,
     parameter bit [3:0]  FEAT_VER = 4'h0,
     parameter bit [23:0] NEXT_DFH_OFFSET = 24'h1000,
     parameter bit END_OF_LIST = 1'b0
   )(
   input clk,
   input reset,
   input [63:0] writedata,
   input read,
   input write,
   input [3:0] byteenable,
   output reg [63:0] readdata,
   output reg readdatavalid,
   input [5:0] address
   );
   
   wire reset_n = !reset;  
   reg [63:0] rdata_comb;
   reg [63:0] scratch_reg;
   
   always @(negedge reset_n ,posedge clk)  
      if (!reset_n) readdata[63:0] <= 64'h0; else readdata[63:0] <= rdata_comb[63:0];
   
   always @(negedge reset_n , posedge clk)
      if (!reset_n) readdatavalid <= 1'b0; else readdatavalid <= read;
   
   wire wr = write;
   wire re = read;
   wire [5:0] addr = address[5:0];
   wire [63:0] din  = writedata [63:0];
   wire wr_scratch_reg = wr & (addr[5:0]  == 6'h30)? byteenable[0]:1'b0;
   
   // 64 bit scratch register
   always @( negedge  reset_n,  posedge clk)
      if (!reset_n)  begin
         scratch_reg <= 64'h0;
      end
      else begin
      if (wr_scratch_reg) begin 
         scratch_reg <=  din;  
      end
   end
   
   always @ (*)
   begin
   rdata_comb = 64'h0000000000000000;
      if(re) begin
         case (addr)  
           6'h00 : begin
                   rdata_comb [11:0]   = FEAT_ID ;  // dfh_feature_id  is reserved or a constant value, a read access gives the reset value
                   rdata_comb [15:12]  = FEAT_VER ;  // dfh_feature_rev    is reserved or a constant value, a read access gives the reset value
                   rdata_comb [39:16]  = NEXT_DFH_OFFSET ;  // dfh_dfh_ofst is reserved or a constant value, a read access gives the reset value
                   rdata_comb [40]     = END_OF_LIST ;        //dfh_end_of_list
                   rdata_comb [59:40]  = 20'h00000 ;  // dfh_rsvd1     is reserved or a constant value, a read access gives the reset value
                   rdata_comb [63:60]  = 4'h3 ;  // dfh_feat_type  is reserved or a constant value, a read access gives the reset value
           end
           6'h30 : begin
                   rdata_comb [63:0]   = scratch_reg; 
           end
           6'h38 : begin
                   rdata_comb [63:0]       = 64'h6626_0701_5000_0034;
           end
           default : begin
                   rdata_comb = 64'h0000000000000000;
           end
         endcase
      end
   end
   
   endmodule
   

6. Create hello_fim_design_files.tcl file.

   touch $OFS_ROOTDIR/src/hello_fim/hello_fim_design_files.tcl
   

   Copy the following code into hello_fim_design_files.tcl

   # Copyright 2023 Intel Corporation.
   #
   # THIS SOFTWARE MAY CONTAIN PREPRODUCTION CODE AND IS PROVIDED BY THE
   # COPYRIGHT HOLDERS AND CONTRIBUTORS "AS IS" AND ANY EXPRESS OR IMPLIED
   # WARRANTIES, INCLUDING, BUT NOT LIMITED TO, THE IMPLIED WARRANTIES OF
   # MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE ARE
   # DISCLAIMED. IN NO EVENT SHALL THE COPYRIGHT HOLDER OR CONTRIBUTORS BE
   # LIABLE FOR ANY DIRECT, INDIRECT, INCIDENTAL, SPECIAL, EXEMPLARY, OR
   # CONSEQUENTIAL DAMAGES (INCLUDING, BUT NOT LIMITED TO, PROCUREMENT OF
   # SUBSTITUTE GOODS OR SERVICES; LOSS OF USE, DATA, OR PROFITS; OR
   # BUSINESS INTERRUPTION) HOWEVER CAUSED AND ON ANY THEORY OF LIABILITY,
   # WHETHER IN CONTRACT, STRICT LIABILITY, OR TORT (INCLUDING NEGLIGENCE
   # OR OTHERWISE) ARISING IN ANY WAY OUT OF THE USE OF THIS SOFTWARE,
   # EVEN IF ADVISED OF THE POSSIBILITY OF SUCH DAMAGE.
   #
   # Hello FIM Files
   #--------------------
   set_global_assignment -name SYSTEMVERILOG_FILE $::env(BUILD_ROOT_REL)/src/hello_fim/hello_fim_com.sv
   set_global_assignment -name SYSTEMVERILOG_FILE $::env(BUILD_ROOT_REL)/src/hello_fim/hello_fim_top.sv
   

7. Modify $OFS_ROOTDIR/syn/board/iseries-dk/syn_top/ofs_top.qsf to include Hello FIM module

   ######################################################
   # Verilog Macros
   ######################################################
   .....
   set_global_assignment -name VERILOG_MACRO "INCLUDE_HELLO_FIM"     # Includes Hello FIM
   

8. Modify $OFS_ROOTDIR/syn/board/iseries-dk/syn_top/ofs_top_sources.tcl to include Hello FIM design files

   ############################################
   # Design Files
   ############################################
   ...
   # Subsystems
   ...
   set_global_assignment -name SOURCE_TCL_SCRIPT_FILE $::env(BUILD_ROOT_REL)/src/hello_fim/hello_fim_design_files.tcl
   

9. Modify $OFS_ROOTDIR/src/pd_qsys/fabric/fabric_design_files.tcl to include BPF Hello FIM Slave IP.

   #--------------------
   # BPF
   #--------------------
   ...
   set_global_assignment -name IP_FILE   $::env(BUILD_ROOT_REL)/src/pd_qsys/fabric/ip/bpf/bpf_hello_fim_slv.ip
   

10. Modify $OFS_ROOTDIR/src/includes/fabric_width_pkg.sv to add Hello FIM slave information and update EMIF slave next offset.

    localparam bpf_hello_fim_slv_baseaddress = 'h16000;    // New
    localparam bpf_hello_fim_slv_address_width = 12;       // New
    localparam bpf_emif_slv_next_dfh_offset = 'h1000;      // Old value: 'hB000
    localparam bpf_hello_fim_slv_next_dfh_offset = 'hA000; // New
    localparam bpf_hello_fim_slv_eol = 'b0;                // New
    

11. Modify $OFS_ROOTDIR/src/top/top.sv

    1. Add bpf_hello_fim_slv_if to AXI interfaces

       // AXI4-lite interfaces
       ...
       ofs_fim_axi_lite_if #(.AWADDR_WIDTH(fabric_width_pkg::bpf_hello_fim_slv_address_width), .ARADDR_WIDTH(fabric_width_pkg::bpf_hello_fim_slv_address_width)) bpf_hello_fim_slv_if();
       

    2. Add Hello FIM instantiation

       //*******************************
       // Hello FIM Subsystem
       //*******************************
       
       `ifdef INCLUDE_HELLO_FIM
       hello_fim_top #(
          .ADDR_WIDTH       (fabric_width_pkg::bpf_hello_fim_slv_address_width),
          .DATA_WIDTH       (64),
          .FEAT_ID          (12'h100),
          .FEAT_VER         (4'h0),
          .NEXT_DFH_OFFSET  (fabric_width_pkg::bpf_hello_fim_slv_next_dfh_offset),
          .END_OF_LIST      (fabric_width_pkg::bpf_hello_fim_slv_eol)
       ) hello_fim_top_inst (
           .clk (clk_csr),
           .reset(~rst_n_csr),
           .csr_lite_if    (bpf_hello_fim_slv_if)
       );
       `else
       dummy_csr #(
          .FEAT_ID          (12'h100),
          .FEAT_VER         (4'h0),
          .NEXT_DFH_OFFSET  (fabric_width_pkg::bpf_hello_fim_slv_next_dfh_offset),
          .END_OF_LIST      (fabric_width_pkg::bpf_hello_fim_slv_eol)
       ) hello_fim_dummy (
          .clk         (clk_csr),
          .rst_n       (rst_n_csr),
          .csr_lite_if (bpf_hello_fim_slv_if)
       );
       
       `endif
       

    3. Add interfaces for Hello FIM slv to bpf instantiation

       bpf bpf (
       ...
         .bpf_hello_fim_slv_awaddr   (bpf_hello_fim_slv_if.awaddr  ),
         .bpf_hello_fim_slv_awprot   (bpf_hello_fim_slv_if.awprot  ),
         .bpf_hello_fim_slv_awvalid  (bpf_hello_fim_slv_if.awvalid ),
         .bpf_hello_fim_slv_awready  (bpf_hello_fim_slv_if.awready ),
         .bpf_hello_fim_slv_wdata    (bpf_hello_fim_slv_if.wdata   ),
         .bpf_hello_fim_slv_wstrb    (bpf_hello_fim_slv_if.wstrb   ),
         .bpf_hello_fim_slv_wvalid   (bpf_hello_fim_slv_if.wvalid  ),
         .bpf_hello_fim_slv_wready   (bpf_hello_fim_slv_if.wready  ),
         .bpf_hello_fim_slv_bresp    (bpf_hello_fim_slv_if.bresp   ),
         .bpf_hello_fim_slv_bvalid   (bpf_hello_fim_slv_if.bvalid  ),
         .bpf_hello_fim_slv_bready   (bpf_hello_fim_slv_if.bready  ),
         .bpf_hello_fim_slv_araddr   (bpf_hello_fim_slv_if.araddr  ),
         .bpf_hello_fim_slv_arprot   (bpf_hello_fim_slv_if.arprot  ),
         .bpf_hello_fim_slv_arvalid  (bpf_hello_fim_slv_if.arvalid ),
         .bpf_hello_fim_slv_arready  (bpf_hello_fim_slv_if.arready ),
         .bpf_hello_fim_slv_rdata    (bpf_hello_fim_slv_if.rdata   ),
         .bpf_hello_fim_slv_rresp    (bpf_hello_fim_slv_if.rresp   ),
         .bpf_hello_fim_slv_rvalid   (bpf_hello_fim_slv_if.rvalid  ),
         .bpf_hello_fim_slv_rready   (bpf_hello_fim_slv_if.rready  ),
       ...
       );
       

12. Modify $OFS_ROOTDIR/src/pd_qsys/fabric/bpf.txt to add the hello_fim module as a slave to the apf.

    # NAME   FABRIC      BASEADDRESS    ADDRESS_WIDTH SLAVES
    apf         mst     n/a             18            fme,pcie,pmci,qsfp0,qsfp1,emif,hssi,hello_fim
    ...
    hello_fim   slv     0x16000         12            n/a
    

13. Execute helper script to generate BPF design files

    cd $OFS_ROOTDIR/src/pd_qsys/fabric/
    
    sh gen_fabrics.sh
    

14. Once the script completes, the following new IP is created: $OFS_ROOTDIR/src/pd_qsys/fabric/ip/bpf/bpf_hello_fim_slv.ip.

15. [OPTIONAL] You may verify the BPF changes have been made correctly by opening bpf.qsys to analyze the BPF.

    cd $OFS_ROOTDIR/src/pd_qsys/fabric
    
    qsys-edit bpf.qsys --quartus-project=$OFS_ROOTDIR/syn/board/iseries-dk/syn_top/ofs_top.qpf
    

    Find the bpf_hello_fim_slv instance:

    

16. Compile the Hello FIM design

    cd $OFS_ROOTDIR
    
    ./ofs-common/scripts/common/syn/build_top.sh -p iseries-dk work_iseries-dk_hello_fim
    

4.1.3 Walkthrough: Modify and run unit tests for a FIM that has a new module

Perform the following steps to modify the unit test files to support a FIM that has had a new module added to it.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

• This walkthrough uses a FIM design that has had a Hello FIM module added to it. Refer to the Add a new module to the OFS FIM section for step-by-step instructions for creating a Hello FIM design. You do not need to compile the design in order to simulate.

Steps:

1. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

2. Modify $OFS_ROOTDIR/sim/unit_test/dfh_walker/test_csr_defs.sv

   1. Add HELLO_FIM_IDX entry to t_dfh_idx enumeration.

      ...
      typedef enum {
          FME_DFH_IDX,
          THERM_MNGM_DFH_IDX,
          GLBL_PERF_DFH_IDX,
          GLBL_ERROR_DFH_IDX,
          QSFP0_DFH_IDX,
          QSFP1_DFH_IDX,
          HSSI_DFH_IDX,
          EMIF_DFH_IDX,
          HELLO_FIM_DFH_IDX,  // New
          PMCI_DFH_IDX,
          ST2MM_DFH_IDX,
          VUART_DFH_IDX,
          PG_PR_DFH_IDX,
          PG_PORT_DFH_IDX,
          PG_USER_CLK_DFH_IDX,
          PG_REMOTE_STP_DFH_IDX,
          AFU_ERR_DFH_IDX,
          MAX_DFH_IDX
      } t_dfh_idx;
      ...
      

   2. Add HELLO_FIM_DFH to get_dfh_names function.

      ...
      function automatic dfh_name[MAX_DFH_IDX-1:0] get_dfh_names();
      ...
        dfh_names[PMCI_DFH_IDX]        = "PMCI_DFH";
        dfh_names[HELLO_FIM_DFH_IDX]   = "HELLO_FIM_DFH";  // New
        dfh_names[ST2MM_DFH_IDX]       = "ST2MM_DFH";
      ...
      return dfh_names;
      ...
      

   3. Add expected DFH value for Hello FIM to the get_dfh_values function.

      ...
      function automatic [MAX_DFH_IDX-1:0][63:0] get_dfh_values();
      ...
        dfh_values[PMCI_DFH_IDX]       = 64'h3_00000_xxxxxx_1012;
        dfh_values[PMCI_DFH_IDX][39:16] = fabric_width_pkg::bpf_pmci_slv_next_dfh_offset;
      
        dfh_values[HELLO_FIM_DFH_IDX]  = 64'h3_00000_xxxxxx_0100;  // New
        dfh_values[HELLO_FIM_DFH_IDX][39:16] = fabric_width_pkg::bpf_hello_fim_slv_next_dfh_offset; // New
      
        dfh_values[ST2MM_DFH_IDX]      = 64'h3_00000_xxxxxx_0014;
        dfh_values[ST2MM_DFH_IDX][39:16] = fabric_width_pkg::apf_st2mm_slv_next_dfh_offset;
      ...
      return dfh_values;
      ...
      

3. Generate simulation files

   cd $OFS_ROOTDIR/ofs-common/scripts/common/sim
   
   ./gen_sim_files.sh iseries-dk
   

4. Run DFH Walker Simulation

   cd $OFS_ROOTDIR/ofs-common/scripts/common/sim
   
   sh run_sim.sh TEST=dfh_walker
   

5. Verify that the test passes, and that the output shows the Hello FIM in the DFH sequence

   ********************************************
    Running TEST(0) : test_dfh_walking
   ********************************************
   
   ...
   
   TX: Tag Search Comparison: CPLD Tag: 00a   Active Tag: 00a
   TX: PU Completion ADDED to transaction!
   TX: Match found for PU CPLD!
   Read64  Method Data Transaction: Address: 0000_0000_0001_5000   Data: 3000_0000_1000_1009
   EMIF_DFH
      Address   (0x15000)
      DFH value (0x3000000010001009)
   
   TX: Tag Search Comparison: CPLD Tag: 00b   Active Tag: 00b
   TX: PU Completion ADDED to transaction!
   TX: Match found for PU CPLD!
   Read64  Method Data Transaction: Address: 0000_0000_0001_6000   Data: 3000_0000_a000_0100
   HELLO_FIM_DFH
      Address   (0x16000)
      DFH value (0x30000000a0000100)
   
   TX: Tag Search Comparison: CPLD Tag: 00c   Active Tag: 00c
   TX: PU Completion ADDED to transaction!
   TX: Match found for PU CPLD!
   Read64  Method Data Transaction: Address: 0000_0000_0002_0000   Data: 3000_0002_0000_1012
   PMCI_DFH
      Address   (0x20000)
      DFH value (0x3000000200001012)
   
   ...
   
   Test status: OK
   
   ********************
     Test summary
   ********************
      test_dfh_walking (id=0) - pass
   Test passed!
   $finish called from file "/home/applications.fpga.ofs.fim-n6001/sim/unit_test/dfh_walker/unit_test.sv", line 236.
   $finish at simulation time 13720.141ns
              V C S   S i m u l a t i o n   R e p o r t
   Time: 13720141000 fs
   CPU Time:      3.290 seconds;       Data structure size:   5.8Mb
   Mon Dec  4 09:27:50 2023
   Total of 5 minutes elapsed for dfh_walker
   run_sim.sh: USER_DEFINED_SIM_OPTIONS +vcs -l ./transcript
   run_sim.sh: run_sim.sh DONE!
   

4.1.4 Walkthrough: Hardware test a FIM that has a new module

Perform the following steps to program and hardware test a FIM that has had a new module added to it.

Pre-requisites:

• This walkthrough requires an OFS Agilex PCIe Attach deployment environment. Refer to the Getting Started Guide: OFS for Agilex® 7 PCIe Attach FPGAs (I-Series Development Kit (2xR-Tile, 1xF-Tile)) for instructions on setting up a deployment environment.

• This walkthrough uses a FIM design that has been generated with a Hello FIM module added to it. Refer to the Add a new module to the OFS FIM section for step-by-step instructions for generating a Hello FIM design.

Steps:

1. [OPTIONAL] In the work directory where the FIM was compiled, determine the PR Interface ID of your design. You can use this value at the end of the walkthrough to verify that the design has been configured to the FPGA.

   cd $OFS_ROOTDIR/<work_directory>/syn/board/iseries-dk/syn_top/
   
   cat fme-ifc-id.txt
   

   Example output:

   b7855572-6ca9-58b8-bd11-44e1f1ab329f
   

2. Switch to your deployment environment.

3. Program the FPGA with the Hello FIM image. Refer to the Program the FPGA via JTAG Section for step-by-step programming instructions.

4. Run fpgainfo to determine the PCIe B:D.F of your board, and to verify the PR Interface ID matches the ID you found in Step 1.

   fpgainfo fme
   

   Example output:

   Intel Acceleration JTAG PCI Development Kit
   //****** FME ******//
   Interface                        : DFL
   Object Id                        : 0xF100000
   PCIe s:b:d.f                     : 0000:B1:00.0
   Vendor Id                        : 0x8086
   Device Id                        : 0xBCCE
   SubVendor Id                     : 0x8086
   SubDevice Id                     : 0x0001
   Socket Id                        : 0x00
   Ports Num                        : 01
   Bitstream Id                     : 360571656856467345 
   Bitstream Version                : 5.0.1
   Pr Interface Id                  : b7855572-6ca9-58b8-bd11-44e1f1ab329f
   Boot Page                        : user
   

5. Initialize opae.io

   sudo opae.io init -d <B:D.F>
   

   For example:

   sudo opae.io init -d b1:00.0
   

6. Run DFH walker. Note the value read back from offset 0x16000 indicates the DFH ID is 0x100 which matches the Hello FIM module.

   sudo opae.io walk -d <B:D.F>
   

   For example:

   sudo opae.io walk -d b1:00.0
   

   Example output:

   ...
   offset: 0x15000, value: 0x3000000010001009
       dfh: id = 0x9, rev = 0x1, next = 0x1000, eol = 0x0, reserved = 0x0, feature_type = 0x3
   offset: 0x16000, value: 0x30000000a0000100
       dfh: id = 0x100, rev = 0x0, next = 0xa000, eol = 0x0, reserved = 0x0, feature_type = 0x3
   offset: 0x20000, value: 0x3000000200001012
       dfh: id = 0x12, rev = 0x1, next = 0x20000, eol = 0x0, reserved = 0x0, feature_type = 0x3
   ...
   

7. Read all of the registers in the Hello FIM module

   1. Read the DFH Register

      opae.io -d b1:00.0 -r 0 peek 0x16000
      

      Example Output:

      0x30000006a0000100
      

   2. Read the Scratchpad Register

      opae.io -d b1:00.0 -r 0 peek 0x16030
      

      Example Output:

      0x0
      

   3. Read the ID Register

      opae.io -d b1:00.0 -r 0 peek 0x16038
      

      Example Output:

      0x6626070150000034
      

8. Verify the scratchpad register at 0x16030 by writing and reading back from it.

   1. Write to Scratchpad register

      opae.io -d b1:00.0 -r 0 poke 0x16030 0x123456789abcdef
      

   2. Read from Scratchpad register

      opae.io -d b1:00.0 -r 0 peek 0x16030
      

      Expected output:

      0x123456789abcdef
      

   3. Write to Scratchpad register

      opae.io -d b1:00.0 -r 0 poke 0x16030 0xfedcba9876543210
      

   4. Read from Scratchpad register

      opae.io -d b1:00.0 -r 0 peek 0x16030
      

      Expected output:

      0xfedcba9876543210
      

9. Release the opae.io tool

   opae.io release -d b1:00.0
   

10. Confirm the driver has been set back to dfl-pci

    opae.io ls
    

    Example output:

    [0000:b1:00.0] (0x8086:0xbcce 0x8086:0x1771) Intel Acceleration JTAG PCI Development Kit (Driver: dfl-pci)
    

4.1.5 Walkthrough: Debug the FIM with Signal Tap

The following steps guide you through the process of adding a Signal Tap instance to your design. The added Signal Tap instance provides hardware to capture the desired internal signals and connect the stored trace information via JTAG. Please be aware that the added Signal Tap hardware will consume FPGA resources and may require additional floorplanning steps to accommodate these resources. Some areas of the FIM use logic lock regions and these regions may need to be re-sized.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

• This walkthrough requires an OFS Agilex PCIe Attach deployment environment. Refer to the Getting Started Guide: OFS for Agilex® 7 PCIe Attach FPGAs (I-Series Development Kit (2xR-Tile, 1xF-Tile)) for instructions on setting up a deployment environment.

• This walkthrough uses a FIM design that has had a Hello FIM module added to it. Refer to the Add a new module to the OFS FIM section for step-by-step instructions for creating a Hello FIM design. You do not need to compile the design.

Perform the following steps in your development environment:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Synthesize the design using the -e build script option. You may skip this step if you are using a pre-synthesized design.

   cd $OFS_ROOTDIR
   
   ./ofs-common/scripts/common/syn/build_top.sh -e iseries-dk work_hello_fim_with_stp
   

4. Open the design in Quartus. The Compilation Dashboard should show that the Analysis & Synthesis step has completed.

   quartus $OFS_ROOTDIR/work_hello_fim_with_stp/syn/board/iseries-dk/syn_top/ofs_top.qpf
   

   

5. Open Tools -> Signal Tap Logic Analyzer

   

   1. Select the Default template and click Create

   2. Assign the clock for sampling the Signal Tap instrumented signals of interest. Note that the clock selected should correspond to the signals you want to view for best trace fidelity. Different clocks can be used, however, there maybe issues with trace inaccuracy due to sampling time differences. This example instruments the hello_fim_top module previously intetegrated into the FIM. If unfamiliar with code, it is helpful to use the Quartus Project Navigator to find the block of interest and open the design instance for review.

      1. In the Signal Configuration -> Clock box of the Signal Tap Logic Analyzer window, click the "..." button

         

      2. In the Node Finder tool that opens, type clock into the Named field, and select hello_fim_top_inst in the Look in field, then click Search. Select the hello_fim_top_inst|clk signal from the Matching Nodes box and click the ">" button to move it to the Nodes Found box. Click OK to close the Node Finder dialog.

         

   3. Update the sample depth and other Signal Tap settings as needed for your debugging criteria.

      

   4. In the Signal Tap GUI add the nodes to be instrumented by double-clicking on the "Double-click to add nodes" legend.

      

   5. This brings up the Node Finder to add the signals to be traced. In this example we will monitor the memory mapped interface to the Hello FIM.

      1. In the Named field, enter csr_lite_if*. In the Look In field, select hello_fim_top_inst.

      2. Select the nets that appear in the Matching Nodes box. Click the > button to add them to the Nodes Found box.

         

      3. Click Insert and close the Node Finder dialog.

   6. To provide a unique name for your Signal Tap instance, select "auto_signaltap_0", right-click, and select Rename Instance (F2). Provide a descriptive name for your instance, for example, stp_for_hello_fim.

      

   7. Save the newly created Signal Tap file, in the $OFS_ROOTDIR/work_hello_fim_with_stp/syn/board/iseries-dk/syn_top/ directory, and give it the same name as the instance. Ensure that the Add file to current project checkbox is ticked.

      

   8. In the dialog that pops up, click "Yes" to add the newly created Signal Tap file to the project settings files.

      

      This will aurtomatically add the following lines to $OFS_ROOTDIR/work_hello_fim_with_stp/syn/board/iseries-dk/syn_top/ofs_top.qsf:

      set_global_assignment -name ENABLE_SIGNALTAP ON
      set_global_assignment -name USE_SIGNALTAP_FILE STP_For_Hello_FIM.stp
      set_global_assignment -name SIGNALTAP_FILE STP_For_Hello_FIM.stp
      

6. Close all Quartus GUIs.

7. Compile the project with the Signal Tap file added to the project. Use the -k switch to perform the compilation using the files in a specified working directory and not the original ones from the cloned repository.

   ./ofs-common/scripts/common/syn/build_top.sh -p -k iseries-dk work_hello_fim_with_stp
   

8. Ensure that the compile completes successfully and meets timing:

   ***********************************
   ***
   ***        OFS_PROJECT: ofs-agx7-pcie-attach
   ***        OFS_BOARD: iseries-dk
   ***        Q_PROJECT:  ofs_top
   ***        Q_REVISION: ofs_top
   ***        SEED: 1
   ***        Build Complete
   ***        Timing Passed!
   ***
   ***********************************
   

9. Set up a JTAG connection to the iseries-dk. Refer to Set up JTAG section for step-by-step instructions.

10. Copy the ofs_top.sof and stp_for_hello_fim.stp files to the machine which is connected to the iseries-dk via JTAG.

11. From the JTAG connected machine, program the $OFS_ROOTDIR/work_hello_fim_with_stp/syn/board/iseries-dk/syn_top/output_files/ofs_top.sof image to the iseries-dk FPGA. Refer to the Program the FPGA via JTAG section for step-by-step programming instructions.

12. Open the Quartus Signal Tap GUI

    $QUARTUS_ROOTDIR/bin/quartus_stpw
    

13. In the Signal Tap Logic Analyzer window, select File -> Open, and choose the stp_for_hello_fim.stp file.

    

14. In the right pane of the Signal Tap GUI, in the Hardware: selection box select the cable for the iseries-dk. In the Device: selection box select the Agilex device.

    

15. If the Agilex Device is not displayed in the Device: list, click the 'Scan Chain' button to re-scan the JTAG device chain.

16. Create the trigger conditions. In this example, we will capture data on a rising edge of the Read Address Valid signal.

    

17. Start analysis by selecting the 'stp_for_hello_fim' instance and pressing 'F5' or clicking the Run Analysis icon in the toolbar. You should see a green message indicating the Acquisition is in progress. Then, move to the Data Tab to observe the signals captured.

    

18. To generate traffic in the csr_lite_if signals of the Hello FIM module, walk the DFH list or peek/poke the Hello FIM registers.

    opae.io init -d 0000:b1:00.0
    opae.io walk -d 0000:b1:00.0
    opae.io release -d 0000:b1:00.0
    

    The signals should be captured on the rising edge of arvalid in this example. Zoom in to get a better view of the signals.

    

4.2 Preparing FIM for AFU Development

In the FIM build, the standard AFUs in the port gasket can be replaced with PIM-based AFUs, wrapped by the ofs_plat_afu() top-level module. Before invoking build_top.sh, set the environment variable AFU_WITH_PIM to the path of a sources text file -- the same sources file from examples such as sources.txt in hello_world:

export AFU_WITH_PIM=<path to>/tutorial/afu_types/01_pim_ifc/hello_world/hw/rtl/axi/sources.txt

When set during the build_top.sh setup stage, the FIM build is configured to load the specified AFU. PR will continue to work, if enabled. The only difference with AFU_WITH_PIM is the change to the AFUs present at power-on. Keep in mind that the default exercisers were chosen to attach to all devices and force reasonable routing decisions during the FIM build across the PR boundary. AFU_WITH_PIM is best used for FIMs that disable PR.

Configuration of the user clock from an AFU's JSON file is ignored in a FIM build.

The AFU_WITH_PIM setting matters only during the setup stage of build_top.sh. It is not consumed by later stages.

4.2.2 Compiling the FIM in preparation for designing your AFU

To save area, the default Host Excercisers in the FIM can be replaced by a "he_null" blocks. There are a few things to note:

• "he_null" is a minimal block with registers that responds to PCIe MMIO request. MMIO responses are required to keep PCIe alive (end points enabled in PCIe-SS needs service downstream requests).
• If an exerciser with other I/O connections such as "he_mem" or "he_hssi" is replaced, then then those I/O ports are simply tied off.
• The options supported are null_he_lb, null_he_hssi, null_he_mem and null_he_mem_tg. Any combination, order or all can be enabled at the same time.
• Finer grain control is provided for you to, for example, turn off only the exercisers in the Static Region in order to save area.

4.2.2.1 Walkthrough: Compile the FIM in preparation for designing your AFU

Perform the following steps to compile a FIM for where the exercisers are removed and replaced with an he_null module while keeping the PF/VF multiplexor connections.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

Steps:

1. Clone the FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Compile the FIM with the HE_NULL compile options

   cd $OFS_ROOTDIR
   
   ./ofs-common/scripts/common/syn/build_top.sh -p iseries-dk:null_he_lb,null_he_hssi,null_he_mem,null_he_mem_tg work_iseries-dk
   

4.3 Partial Reconfiguration Region

To take advantage of the available resources in the Agilex® 7 FPGA for an AFU design, you can adjust the size of the AFU PR partition. An example reason for the changing the size of PR region is if you add more logic to the FIM region, then you may need to adjust the PR region to fit the additional logic into the static region. Similarly, if you reduce logic in the FIM region, then you can adjust the PR region to provide more logic resources for the AFU.

After the compilation of the FIM, the resources usage broken down by partitions as reported in the following file:

$OFS_ROOTDIR/<WORDK_DIRECTORY>/syn/board/iseries-dk/syn_top/output_files/ofs_top.fit.rpt

An example report of the resources usage by partitions defined for the FIM is shown as follows:

+------------------------------------------------------------------------------------------+
; Logic Lock Region Constraints                                                            ;
+--------------------------------------+-------------------------+-------------------------+
; Name                                 ; Place Region Constraint ; Route Region Constraint ;
+--------------------------------------+-------------------------+-------------------------+
; afu_top|port_gasket|pr_slot|afu_main ; (90, 40) to (350, 220)  ; (0, 0) to (385, 329)    ;
+--------------------------------------+-------------------------+-------------------------+


+----------------------------------------------------------------------------------------------+
; Logic Lock Region Usage Summary                                                              ;
+-------------------------------------------------------+--------------------------------------+
; Statistic                                             ; afu_top|port_gasket|pr_slot|afu_main ;
+-------------------------------------------------------+--------------------------------------+
; ALMs needed [=A-B+C]                                  ; 48011.2 / 351140 ( 13 % )            ;
;     [A] ALMs used in final placement                  ; 53324.4 / 351140 ( 15 % )            ;
;     [B] Estimate of ALMs recoverable by dense packing ; 5452.3 / 351140 ( 1 % )              ;
;     [C] Estimate of ALMs unavailable                  ; 139.0 / 351140 ( < 1 % )             ;
; ALMs used for memory                                  ; 450.0                                ;
; Combinational ALUTs                                   ; 67166                                ;
; Dedicated Logic Registers                             ; 87533 / 1404560 ( 6 % )              ;
; I/O Registers                                         ; 0                                    ;
; Block Memory Bits                                     ; 1737568                              ;
; M20Ks                                                 ; 137 / 5049 ( 2 % )                   ;
; DSP Blocks needed [=A-B]                              ; 0 / 3439 ( 0 % )                     ;
;     [A] DSP Blocks used in final placement            ; 0 / 3439 ( 0 % )                     ;
;     [B] Estimate of DSPs recoverable by dense merging ; 0 / 3439 ( 0 % )                     ;
; Pins                                                  ; 0                                    ;
; IOPLLs                                                ; 0                                    ;
;                                                       ;                                      ;
; Region Placement                                      ; (90, 40) to (350, 220)               ;
+-------------------------------------------------------+--------------------------------------+

In this case, the default size for the afu_top|port_gasket|pr_slot|afu_main PR partition is large enough to hold the logic of the default AFU, which is mainly occupied by the Host Exercisers. However, larger designs might require additional resources.

4.3.1 Walkthrough: Resize the Partial Reconfiguration Region

Perform the following steps to first analyze the PR logic lock regions in a default FIM design, then resize the PR region:

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. The OFS flow provides the TCL file $OFS_ROOTDIR/syn/board/iseries-dk/setup/pr_assignments.tcl which defines the PR partition where the AFU is allocated. Each region is a rectangle defined by the origin coordinate (X0, Y0) and the top right corner coordinate (X1, Y1).

   #####################################################
   # Main PR Partition -- green_region
   #####################################################
   set_instance_assignment -name PARTITION green_region -to afu_top|pg_afu.port_gasket|pr_slot|afu_main
   set_instance_assignment -name CORE_ONLY_PLACE_REGION ON -to afu_top|pg_afu.port_gasket|pr_slot|afu_main
   set_instance_assignment -name RESERVE_PLACE_REGION ON -to afu_top|pg_afu.port_gasket|pr_slot|afu_main
   set_instance_assignment -name PARTIAL_RECONFIGURATION_PARTITION ON -to afu_top|pg_afu.port_gasket|pr_slot|afu_main
   
   
   set_instance_assignment -name PLACE_REGION "X90 Y40 X350 Y220" -to afu_top|pg_afu.port_gasket|pr_slot|afu_main
   set_instance_assignment -name ROUTE_REGION "X0 Y0 X385 Y329" -to afu_top|pg_afu.port_gasket|pr_slot|afu_main
   

4. [OPTIONAL] Use Quartus Chip Planner to visualize the default PR region allocation.

   1. Compile the design.

      ./ofs-common/scripts/common/syn/build_top.sh iseries-dk work_iseries-dk
      

   2. Once the design is compiled, open it in Quartus.

      quartus $OFS_ROOTDIR/work_iseries-dk/syn/board/iseries-dk/syn_top/ofs_top.qpf
      

   3. Switch to the ofs_top view if necessary.

      

   4. Click Tools -> Chip Planner to open the Chip Planner.

   5. Analyze the regions shown. Note that the regions are made of rectangles described by an origin coordinate, region height, and region width. If you are modifying the regions, you will need to identify the coordinates of your desired region.

      

   6. Close the Quartus GUI.

5. Make changes to the partial reconfiguraton region in the $OFS_ROOTDIR/syn/board/iseries-dk/setup/pr_assignments.tcl file. You can modify the size and location of existing lock regions or add new ones and assign them to the AFU PR partition.

6. Recompile your FIM and create the PR relocatable build tree using the following commands.

   cd $OFS_ROOTDIR    
   
   ofs-common/scripts/common/syn/build_top.sh -p iseries-dk work_iseries-dk_resize_pr
   

7. Analyze the resource utilization report $OFS_ROOTDIR/work_iseries-dk/syn/board/iseries-dk/syn_top/output_files/ofs_top.fit.rpt produced after recompiling the FIM.

8. Perform further modification to the PR regions until the results are satisfactory. Make sure timing constraints are met.

For more information on how to optimize the floor plan of your Partial Reconfiguration design refer to the following online documentation.

• Analyzing and Optimizing the Design Floorplan

• Partial Reconfiguration Design Flow - Step 3 - Floorplan the Design

4.4 PCIe Configuration

The PCIe Subsystem can be easily modified using OFS provided script and the PCIe subsystem IP core. In this section both the PCIe SR-IOV configuration and PCIe configuration registers will be modified. You can use this process for setting up your specific settings.

The PCIe configuration for the iseries-dk can be set to 1x16 or bifurcated 2x8. You must ensure that the server you are using is set according to the design you are using. You can use OFSS to select which configuration to build with. Refer to the PCIe Configuration Using OFSS section for details. The following OFSS files are provided to you in the source repository:

• PCIe 1xGen5x16: $OFS_ROOTDIR/tools/ofss_config/pcie/pcie_host.ofss
• PCIe 2xGen5x8: $OFS_ROOTDIR/tools/ofss_config/pcie/pcie_host_2link.ofss
• PCIe 1xGen4x16: $OFS_ROOTDIR/tools/ofss_config/pcie/pcie_host_gen4.ofss

As of the OFS 2024.2 release, the PCIe-SS uses the AXI Streaming Intel FPGA IP for PCI Express by default, which does not support Data Mover Mode. OFS releases prior to OFS 2024.2 used the PCIe Subsystem Intel FPGA IP which does support Data Mover Mode. If Data Mover Mode is required, you must change the target IP in the PCIe OFSS file. A walkthrough is provided later in this section. Note that the older IP does not support the PCIe Gen5x16 configuration; it only supports Gen5 2x8 or Gen4 1x16. A walkthrough for these changes is provided later in this section.

4.4.1 PF/VF MUX Configuration

The default PF/VF MUX configuration for OFS PCIe Attach FIM for the n6001 can support up to 8 PFs and 2000 VFs distributed accross all PFs.

For reference FIM configurations, you must have at least 1 PF with 1VF, or 2PFs. This is because the PR region cannot be left unconnected. PFs must be consecutive. The PFVF Limitations table describes the supported number of PFs and VFs.

Table: PF/VF Limitations

Parameter	Value
Min # of PFs	1 (if at least 1 VF present) | 2 (if no VFs present)
Max # of PFs	8
Min # of VFs	1 on PF0 (if only 1 PF present) | 0 (if 2PFs present)
Max # of VFs	2000 distributed across all PFs

Note that as the number of VFs goes up, timing closure can become more difficult.

The scripts provided in ${OFS_ROOTDIR}/ofs-common/tools/ofss_config allows you to easily reconfigure the number of PFs and VFs, bar addresses, vendor/device ID values and more. The PCIe Subsystem IP parameters that can be modified can be seen by reviewing ${OFS_ROOTDIR}/ofs-common/tools/ofss_config/ip_params/pcie_ss_component_parameters.py

New PF or VF instances will automatically have a null_afu module instantiated and connected to the new PF or VF.

4.4.2 PCIe-SS Configuration Registers

The PCIe-SS configuration registers contain the Vendor, Device and Subsystem Vendor ID registers which are used in PCIe add-in cards to uniquely identify the card for assignment to software drivers. OFS has these registers set with Intel values for out of the box usage. If you are using OFS for a PCIe add in card that your company manufactures, then update the PCIe Subsytem Subsystem ID and Vendor ID registers as described below and change OPAE provided software code to properly operate with your company's register values.

The Vendor ID is assigned to your company by the PCI-SIG (Special Interest Group). The PCI-SIG is the only body officially licensed to give out IDs. You must be a member of PCI-SIG to request your own ID. Information about joining PCI-SIG is available here: PCI-SIG. You select the Subsystem Device ID for your PCIe add in card.

4.4.3 PCIe Configuration Using OFSS

The general flow for using OFSS to modify the PCIe Sub-system and PF/VF MUX is as follows:

1. Create or modify a PCIe OFSS file with the desired PCIe configuration.
2. Call this PCIe OFSS file when running the FIM build script.

The PCIe IP OFSS File Options table lists all of the configuration options supported by the OFSS flow. Any other customizations to the PCIe sub-system must be done with the IP Presets Flow.

Table: PCIe IP OFSS File Options

Section	Parameter	Options	Default	Description
[ip]	type	pcie	N/A	Specifies that this OFSS file configures the PCIe-SS
[settings]	output_name	pcie_ss	N/A	Specifies the output name of the PCIe-SS IP
	preset	String	N/A	OPTIONAL - Specifies the name of a PCIe-SS IP presets file to use when building the FIM. When used, a presets file will take priority over any other parameters set in this OFSS file.
	pcie_gen	4 | 5	N/A	Specifies the PCIe generation
	pcie_instances	1 | 2	N/A	Specifies the number of PCIe instances. When set to 1 the PCIe configuration will be 1x16. When set to 2 the PCIe configuration will be x8; the pcie_instances_enabled parameter will determine if it is 2x8 or 1x8.
	pcie_instances_enabled	1 | 2	N/A	Specifies the number of PCIe instances that are enabled. When set to 2 the PCIe configuration will be 2x8 if; when set to 1 the PCIe configuration will be 1x16. Use only when the pcie_instances parameter is set to 2.
[pf*]	num_vfs	Integer	0	Specifies the number of Virtual Functions in the current PF
	bar0_address_width	Integer	12
	bar4_address_width	Integer	14
	vf_bar0_address_width	Integer	12
	ats_cap_enable	0 | 1	0
	vf_ats_cap_enable	0 | 1	0
	prs_ext_cap_enable	0 | 1	0
	pasid_cap_enable	0 | 1	0
	pci_type0_vendor_id	32'h Value	0x00008086
	pci_type0_device_id	32'h Value	0x0000bcce
	revision_id	32'h Value	0x00000001
	class_code	32'h Value	0x00120000
	subsys_vendor_id	32'h Value	0x00008086
	subsys_dev_id	32'h Value	0x00000001
	sriov_vf_device_id	32'h Value	0x0000bccf
	exvf_subsysid	32'h Value	0x00000001

4.4.3.1 Walkthrough: Modify the PCIe Sub-System and PF/VF MUX Configuration Using OFSS

Perform the following steps to use OFSS files to configure the PCIe Sub-system and PF/VF MUX. In this example both the PCIe SR-IOV configuration and PCIe configuration registers will be modified.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

• To demonstrate updated PCIe PF/VF in hardware, use an OFS Agilex I-Series PCIe Attach deployment environment. Refer to the Getting Started Guide: OFS for Agilex® 7 PCIe Attach FPGAs (I-Series Development Kit (2xR-Tile, 1xF-Tile)) for instructions on setting up a deployment environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. View the default OFS PCIe Attach FIM for the iseries-dk PF/VF configuration in the the $OFS_ROOTDIR/tools/ofss_config/pcie/pcie_host.ofss file.

   [ip]
   type = pcie
   
   [settings]
   output_name = pcie_ss
   
   [pf0]
   num_vfs = 3
   bar0_address_width = 20
   vf_bar0_address_width = 20
   
   [pf1]
   
   [pf2]
   bar0_address_width = 18
   
   [pf3]
   
   [pf4]
   

4. Create a new PCIe OFSS file from the existing pcie_host.ofss file

   cp $OFS_ROOTDIR/tools/ofss_config/pcie/pcie_host.ofss $OFS_ROOTDIR/tools/ofss_config/pcie/pcie_pfvf_mod.ofss
   

5. Configure the new pcie_pfvf_mod.ofss with your desired PCIe settings. In this example we will add PF5 with 2 VFs.

   [ip]
   type = pcie
   
   [settings]
   output_name = pcie_ss
   
   [pf0]
   num_vfs = 3
   bar0_address_width = 20
   vf_bar0_address_width = 20
   
   [pf1]
   
   [pf2]
   bar0_address_width = 18
   
   [pf3]
   
   [pf4]
   
   [pf5]
   num_vfs = 2
   

6. Compile the FIM with the new PCIe OFSS file.

   cd $OFS_ROOTDIR
   
   ./ofs-common/scripts/common/syn/build_top.sh -p --ofss tools/ofss_config/pcie/pcie_pfvf_mod.ofss iseries-dk work_iseries-dk_pfvf_mod
   

7. Copy the resulting $OFS_ROOTDIR/work_iseries-dk_pfvf_mod/syn/board/iseries-dk/syn_top/output_files/ofs_top.sof image to your deployment environmenment.

8. Switch to your deployment environment.

9. Program the ofs_top.sof image to the iseries-dk FPGA. Refer to the Program the FPGA via JTAG Section for step-by-step programming instructions.

10. Verify the number of VFs on the newly added PF5. In this example, we defined 2 VFs on PF5 in Step 5.

    sudo lspci -vvv -s b1:00.5 | grep VF
    

    Example output:

    Initial VFs: 2, Total VFs: 2, Number of VFs: 0, Function Dependency Link: 05
    VF offset: 4, stride: 1, Device ID: bccf
    VF Migration: offset: 00000000, BIR: 0
    

11. Verify communication with the newly added PF5. New PF/VF are seamlessly connected to their own CSR stub, which can be read at DFH Offset 0x0. You can bind to the function and perform opae.io peek commands to read from the stub CSR. Similarly, perform opae.io poke commands to write into the stub CSRs. Use this mechanism to verify that the new PF/VF Mux configuration allows to write and read back values from the stub CSRs.

    The GUID for every new PF/VF CSR stub is the same.

    * NULL_GUID_L           = 64'haa31f54a3e403501
    * NULL_GUID_H           = 64'h3e7b60a0df2d4850
    

    1. Initialize the driver on PF5

       sudo opae.io init -d b1:00.5
       

    2. Read the GUID for the PF5 CSR stub.

       sudo opae.io -d b1:00.5 -r 0 peek 0x8
       sudo opae.io -d b1:00.5 -r 0 peek 0x10
       

       Example output:

       0xaa31f54a3e403501
       0x3e7b60a0df2d4850
       

4.4.3.2 Walkthrough: Build the 2x8 PCIe Sub-System

Perform the following steps to use OFSS files to build the FIM with a 2xGen5x8 PCIe configuration.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

• To demonstrate updated PCIe PF/VF in hardware, use an OFS Agilex I-Series PCIe Attach deployment environment. Refer to the Getting Started Guide: OFS for Agilex® 7 PCIe Attach FPGAs (I-Series Development Kit (2xR-Tile, 1xF-Tile)) for instructions on setting up a deployment environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Build the FIM with the 2xGen5x16 PCIe configuration.

   cd $OFS_ROOTDIR
   
   ./ofs-common/scripts/common/syn/build_top.sh --ofss $OFS_ROOTDIR/tools/ofss_config/pcie/pcie_host_2link.ofss iseries-dk work_iseries-dk
   

4. When the build script completes, copy the resulting $OFS_ROOTDIR/work_iseries-dk/syn/board/iseries-dk/syn_top/output_files/ofs_top.sof to your deployment environment if it is different than your development environment.

5. Switch to your deployment environment.

Note: Ensure that your server is configured for PCIe 2x8 bifurcated mode before continuing.

1. Program the ofs_top.sof image to the iseries-dk FPGA. Refer to the Program the FPGA via JTAG Section for step-by-step programming instructions.

2. Verify the 6 PFs (3 for each link) are present with proper device ID. Not the PCIe B:D.F for each as this will be used later.

   $ lspci | grep bcce
   

   Example output:

   ac:00.0 Processing accelerators: Intel Corporation Device bcce (rev 01)
   ac:00.1 Processing accelerators: Intel Corporation Device bcce (rev 01)
   ac:00.2 Processing accelerators: Intel Corporation Device bcce (rev 01)
   ad:00.0 Processing accelerators: Intel Corporation Device bcce (rev 01)
   ad:00.1 Processing accelerators: Intel Corporation Device bcce (rev 01)
   ad:00.2 Processing accelerators: Intel Corporation Device bcce (rev 01)
   

3. Verify the new VFs can be added. Use the OPAE SDK command pci_device to create VFs. Verify PF 0 has the proper number of VFs and have device ID of bccf.

   sudo pci_device ac:00.0 vf 3
   sudo pci_device ad:00.3 vf 3
   

4. Verify that the VFs have been added.

   ```bash sudo lspci -vvv -s ac:00.0 | grep VF sudo lspci -vvv -s ad:00.0 | grep VF

   Example Outputs:
   
   ```bash
   Initial VFs: 3, Total VFs: 3, Number of VFs: 3, Function Dependency Link: 00
   VF offset: 3, stride: 1, Device ID: bccf
   VF Migration: offset: 00000000, BIR: 0
   
   Initial VFs: 3, Total VFs: 3, Number of VFs: 3, Function Dependency Link: 00
   VF offset: 3, stride: 1, Device ID: bccf
   VF Migration: offset: 00000000, BIR: 0
   

4.4.4 PCIe Configuration Using IP Presets

The general flow for using IP Presets to modify he PCIe Sub-system is as follows:

1. [OPTIONAL] Create a work directory using OFSS files if you wish to use OFSS configuration settings.
2. Open the PCIe-SS IP and make desired modifications.
3. Create an IP Presets file.
4. Create an PCIe OFSS file that uses the IP Presets file.
5. Build the FIM with the PCIe OFSS file from Step 4.

4.4.4.1 Walkthrough: Modify PCIe Configuration Using IP Presets

Perform the following steps to use OFSS files to configure the PCIe Sub-system and PF/VF MUX. In this example, we will change the Revision ID of PF0. While this modification can be done with the OFSS flow, this walkthrough is intended to show the procedure for making any PCIe configuration change using IP presets.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

• To demonstrate updated PCIe PF/VF in hardware, use an OFS Agilex I-Series PCIe Attach deployment environment. Refer to the Getting Started Guide: OFS for Agilex® 7 PCIe Attach FPGAs (I-Series Development Kit (2xR-Tile, 1xF-Tile)) for instructions on setting up a deployment environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Run the setup stage of the build script using your desired OFSS configration to create a working directory for the iseries-dk design.

   ./ofs-common/scripts/common/syn/build_top.sh --stage setup iseries-dk work_iseries-dk
   

4. Open the PCIe-SS in the work directory using Quartus Parameter Editor.

   qsys-edit $OFS_ROOTDIR/work_iseries-dk/ipss/pcie/qip/pcie_ss.ip
   

5. In the IP Parameter Editor window, scroll down and select the PCIe Interfaces Port Settings -> Port 0 -> PCIe0 Device Identification Registers -> PCIe0 PF0 IDs tab. Modify the settings as desired. In this case, we are changing the Revision ID to 0x00000002. You may make any desired modifications.

   

6. Once you are satisfied with your modifcations, create a new IP Preset file.

   1. click New... in the Presets window.

      

   2. In the New Preset window, set a unique Name for the preset; for example, iseries-dk-rev2.

      

   3. Click the ... button to set the save location for the IP Preset file to $OFS_ROOTDIR/ipss/pcie/presets. Set the File Name to match the name selected in Step 9. Click OK.

      

   4. In the New Preset window, click Save. Click No when prompted to add the file to the IP search path.

      

7. Close IP Parameter Editor without saving or generating HDL.

8. Create a new PCIe OFSS file in the $OFS_ROOTDIR/tools/ofss_config/pcie directory. For example:

   touch $OFS_ROOTDIR/tools/ofss_config/pcie/pcie_host_mod_preset.ofss
   

   Insert the following into the OFSS file to specify the IP Preset file created in Step 8.

   [ip]
   type = pcie
   
   [settings]
   output_name = pcie_ss
   preset = iseries-dk-rev2
   

9. Compile the design with the modified new pcie_host_mod_preset.ofss file.

   cd $OFS_ROOTDIR
   
   ./ofs-common/scripts/common/syn/build_top.sh -p --ofss tools/ofss_config/pcie/pcie_host_mod_preset.ofss iseries-dk work_iseries-dk_pcie_mod
   

10. Copy the resulting $OFS_ROOTDIR/work_fseries-dk_pcie_mod/syn/board/fseries-dk/syn_top/output_files/ofs_top.sof image to your deployment environmenment.

11. Switch to your deployment environment.

12. Program the ofs_top.sof image to the iseries-dk FPGA. Refer to the Program the FPGA via JTAG Section for step-by-step programming instructions.

13. Determing the PCIe B:D.F of your board. You may use the OPAE command fpgainfo fme to determine this.

    fpgainfo fme
    

    Example output:

    Intel Acceleration JTAG PCI Development Kit
    //****** FME ******//
    Interface                        : DFL
    Object Id                        : 0xF100000
    PCIe s:b:d.f                     : 0000:B1:00.0
    Vendor Id                        : 0x8086
    Device Id                        : 0xBCCE
    SubVendor Id                     : 0x8086
    SubDevice Id                     : 0x0001
    Socket Id                        : 0x00
    Ports Num                        : 01
    Bitstream Id                     : 360571656856467345 
    Bitstream Version                : 5.0.1
    Pr Interface Id                  : b7855572-6ca9-58b8-bd11-44e1f1ab329f
    Boot Page                        : user
    

14. Use lspci with the PCIe B:D.F of your board to verify that the PCIe changes have been implemented. In this example, the Rev for PF0 is 02.

    lspci -nvmms 84:00.0
    

    Example output:

    Slot:   84:00.0
    Class:  1200
    Vendor: 8086
    Device: bcce
    SVendor:        8086
    SDevice:        0001
    PhySlot:        1-1
    Rev:    01
    NUMANode:       1
    IOMMUGroup:     190
    

**4.4.5 PCIe Sub-System Target IP **

As of the OFS 2024.2 release, the PCIe-SS uses the AXI Streaming Intel FPGA IP for PCI Express by default, which does not support Data Mover Mode. OFS releases prior to OFS 2024.2 used the PCIe Subsystem Intel FPGA IP which does support Data Mover Mode. If Data Mover Mode is required, you must change the target IP in the PCIe OFSS file. A walkthrough is provided later in this section. Note that the older IP does not support the PCIe Gen5x16 configuration; it only supports Gen5 2x8 or Gen4 1x16.

4.4.5.1 Walkthrough: Change the PCIe Sub-System Target IP

Perform the following steps to change the target PCIe IP from AXI Streaming Intel FPGA IP for PCI Express to Intel FPGA IP Subsystem for PCI Express.

Pre-requisites:

• This walkthrough requires a development environment to build the FIM. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Add the following line to the [settings] section of the PCIe OFSS file you are using. In this example, it will be added to the $OFS_ROOTDIR/tools/ofss_config/pcie/pcie_host_2link.ofss file. Note that the older IP does not support the PCIe Gen5x16 configuration; it only supports Gen5 2x8 or Gen4 1x16. By using the pcie_host_2link.ofss file, the PCIe configuration will be Gen5 2x8.

   ip_component = pcie_ss
   

   Note: To change back to using the AXI Streaming Intel FPGA IP for PCI Express, simply remove this line.

4. Build the FIM using the 470 MHz IOPLL and the PCIe OFSS file that was modified in step 3.

   ./ofs-common/scripts/common/syn/build_top.sh --ofss tools/ofss_config/iopll/iopll_470MHz.ofss,tools/ofss_config/pcie/pcie_host_2link.ofss iseries-dk work_${{ env.ISERIS_DK_MODEL}}
   

5. When the build completes, the output files can be found in $OFS_ROOTDIR/work_iseries-dk/syn/board/iseries-dk/output_files.

4.5 Minimal FIM

In a minimal FIM, the exercisers and Ethernet subsystem are removed from the design, the PF/VF configuration is reduced to either 2PF/0VF or 1PF/1VF, and the AFU PR area is expanded to make use of the available area previously used by the removed components.

There are two pre-provided PCIe configurations that can be used to create minimal FIM.

• 2PF: this PCIe configuration has two physical functions, with the APF/BPF on PF0, and the AFU PR region on PF1.

• 1PF/1VF: This PCIe configuration has a single physical function, with the APF/BPF on PF0, and the AFU PR region on PF0-VF0.

Block diagrams for the PCIe 2x8 and PCIe 1x16 configurations are shown below.

• PCIe 1x16 Minimal Fim

  

• PCIe 2x8 Minimal Fim

  

The FIM source repository contains OFSS file that can be used to configure the PCIe IP for the minimal FIM.

• $OFS_ROOTDIR/tools/ofss_config/pcie/pcie_host_2pf.ofss
• $OFS_ROOTDIR/tools/ofss_config/pcie/pcie_host_1pf_1vf.ofss
• $OFS_ROOTDIR/tools/ofss_config/pcie/pcie_host_2link_1pf_1vf.ofss

4.5.1 Create a Minimal FIM

Perform the following steps to create a Minimal FIM.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

• This walkthrough requires an OFS Agilex PCIe Attach deployment environment for hardware testing. Refer to the Getting Started Guide: OFS for Agilex® 7 PCIe Attach FPGAs (I-Series Development Kit (2xR-Tile, 1xF-Tile)) for instructions on setting up a deployment environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. The OFS FIM repo provides a PR assignments TCL file which optimizes the PR region for the minimal FIM. Copy the minimal PR assignments TCL file into the pr_assignments.tcl file location for use in the FIM build process.

   1. Rename the current pr_assignments.tcl file to pr_assignments_base.tcl for future use

      mv $OFS_ROOTDIR/syn/board/iseries-dk/setup/pr_assignments.tcl $OFS_ROOTDIR/syn/board/iseries-dk/setup/pr_assignments_base.tcl
      

   2. Copy the pr_assignments_slim.tcl file to pr_assignments.tcl to be used in the current build

      cp $OFS_ROOTDIR/syn/board/iseries-dk/setup/pr_assignments_slim.tcl $OFS_ROOTDIR/syn/board/iseries-dk/setup/pr_assignments.tcl
      

4. Compile the FIM with Null HEs compile option, the No HSSI compile option, and the desired PCIe PF/VF configuration.

   cd $OFS_ROOTDIR
   

   • PCIe 1x16 2PF Minimal FIM

     ./ofs-common/scripts/common/syn/build_top.sh -p --ofss tools/ofss_config/pcie/pcie_host_2pf.ofss iseries-dk:null_he_lb,null_he_hssi,null_he_mem,null_he_mem_tg,no_hssi work_iseries-dk_minimal_fim
     

   • PCIe 1x16 1PF/1VF Minimal FIM

     ./ofs-common/scripts/common/syn/build_top.sh -p --ofss tools/ofss_config/pcie/pcie_host_1pf_1vf.ofss iseries-dk:null_he_lb,null_he_hssi,null_he_mem,null_he_mem_tg,no_hssi work_iseries-dk_minimal_fim
     

   • PCIe 2x8 1PF/1VF Minimal FIM

     ./ofs-common/scripts/common/syn/build_top.sh -p --ofss tools/ofss_config/pcie/pcie_host_2link_1pf_1vf.ofss iseries-dk:null_he_lb,null_he_hssi,null_he_mem,null_he_mem_tg,no_hssi work_iseries-dk_minimal_fim
     

5. Review the $OFS_ROOTDIR/work_iseries-dk/syn/board/iseries-dk/syn_top/output_files/ofs_top.fit.rpt utilization report to see the utilization statistics for the Minimal fim. Refer to Appendix A: Resource Utilization Tables Table A-4 for the expected utilization for this Minimal FIM.

6. Copy the resulting $OFS_ROOTDIR/work_iseries-dk/syn/board/iseries/syn_top/output_files/ofs_top.sof image to your deployment environmenment.

7. Switch to your deployment environment, if different than your development environment.

8. Program the ofs_top.sof image to the iseries-dk FPGA. Refer to the Program the FPGA via JTAG Section for step-by-step programming instructions.

9. Use lspci to verify that the PCIe changes have been implemented.

   sudo lspci -vvv -s b1:00.0 | grep VF
   

   Example output for a 1PF/1VF image:

   Initial VFs: 1, Total VFs: 1, Number of VFs: 0, Function Dependency Link: 00
   VF offset: 1, stride: 1, Device ID: bcce
   VF Migration: offset: 00000000, BIR: 0
   

4.6 Migrating to a Different Agilex Device Number

The following instructions enable a user to change the device part number of the Agilex® 7 FPGA I-Series Development Kit (2x R-Tile and 1xF-Tile). Please be aware that this release works with Agilex® 7 FPGA devices that have F-tile for PCIe and Ethernet. Other tiles will take further work.

You may wish to change the device part number for the following reasons

1. Migrate to same device package but with a different density
2. Migrate to a different package and with a different or same density

The default device for the Agilex® 7 FPGA I-Series Development Kit (2x R-Tile and 1xF-Tile) is AGIB027R29A1E2VR3

4.6.1 Walkthrough: Migrate to a Different Agilex Device Number

Perform the following steps to migrate to a different Agilex Device. In this example, we will migrate from the default AGIB027R29A1E2VR3 device to AGIB027R31A1E2VB. The package will change from R29A to R31A.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Modify the part field in the $OFS_ROOTDIR/tools/ofss_config/iseries-dk_base.ofss file to use AGIB027R31A1E2VB.

   [ip]
   type = ofs
   
   [settings]
   platform = n6001
   family = agilex
   fim = base_x16
   part = AGIB027R31A1E2VB 
   device_id = 6001
   

4. Modify the DEVICE field in the $OFS_ROOTDIR/syn/board/iseries-dk/syn_top/ofs_top.qsf file to use AGIB027R31A1E2VB.

   ############################################################################################
   # FPGA Device
   ############################################################################################
   
   set_global_assignment -name FAMILY "Agilex 7"
   set_global_assignment -name DEVICE AGIB027R31A1E2VB 
   

5. Modify the DEVICE field in the $OFS_ROOTDIR/syn/board/iseries-dk/syn_top/ofs_pr_afu.qsf file to use AGIB027R31A1E2VB.

   ############################################################################################
   # FPGA Device
   ############################################################################################
   
   set_global_assignment -name FAMILY Agilex 7
   set_global_assignment -name DEVICE AGIB027R31A1E2VB 
   

6. If the device you are migrating to uses the same package and pinout, you do not need to modify the pinout constraints. In this example, because we are migrating from package R29A to R31A, we need to modify the pinout to match the new device. If you would like Quartus to attempt to pin out the design automatically, you may remove all pin assignments. Typically, you will still need to set certain pins manually in order to guide Quartus for a successful compile (e.g. transceiver reference clocks).

   1. Commment out all pin assignments in the following files: * $OFS_ROOTDIR/syn/board/iseries-dk/setup/emif_loc.tcl * $OFS_ROOTDIR/syn/board/iseries-dk/setup/top_loc.tcl

   2. Identify the pins in the design that will be constrained. In this example we will manually constrain the QSFP reference clock and the PCIe reference clock to help guide the fitter. The Device Migration Pinout Table shows the pin assignments that will be set, along with the pin number for both the old R24C package and the new R31C package.

      Net Name	R29A Pin Name	R31A Pin Name	AGI 027 R29A Pin #	AGI 027 R31A Pin #
      qsfp_ref_clk	REFCLK_FGTL12A_Q2_RX_CH4p	REFCLK_FGTL12C_Q2_RX_CH4p	JD74	AM57
      PCIE_REFCLK0	REFCLK_GXRL14C_CH0p	REFCLK_GXRL14A_CH0p	DR68	BU56
      PCIE_REFCLK1	REFCLK_GXRL14C_CH1p	REFCLK_GXRL14A_CH1p	CU68	BP57

   3. Re-pin the pins identified in the previous step in the $OFS_ROOTDIR/syn/board/iseries-dk/setup/top_loc.tcl file for the new pinout for the AGF 027 R31C package.

      set_location_assignment PIN_AM57 -to qsfp_ref_clk
      
      set_location_assignment PIN_BU56 -to PCIE_REFCLK0
      set_location_assignment PIN_BP57 -to PCIE_REFCLK1
      

   4. Uncomment the instance assignments related to he QSFP and PCIe reference clocks in the $OFS_ROOTDIR/syn/board/iseries-dk/setup/top_loc.tcl file.

      set_instance_assignment -name IO_STANDARD "CURRENT MODE LOGIC (CML)" -to qsfp_ref_clk
      
      set_instance_assignment -name IO_STANDARD HCSL -to PCIE_REFCLK0
      set_instance_assignment -name IO_STANDARD HCSL -to PCIE_REFCLK1
      

7. Compile a flat design. It is recommended to compile a flat design first before incorporating a PR region in the design. This reduces design complexity while you determine the correct pinout for your design.

   cd $OFS_ROOTDIR
   
   ./ofs-common/scripts/common/syn/build_top.sh ${{ env.ISERIS_DK_MODEL }}:flat work_${{ env.ISERIS_DK_MODEL }}
   

8. Verify that the build completes successfuly. If the compilation fails with errors relating to the pinout, review the error messages and modify the pinout accordingly. If there are timing violations, try building with a different seed. Refer to the Change the Compilation Seed section for instructions on changing the build seed.

9. When you are satisfied with the pinout, preserve it by hard-coding the desired pinout back to the followig files:

   • $OFS_ROOTDIR/syn/board/iseries-dk/setup/emif_loc.tcl
   • $OFS_ROOTDIR/syn/board/iseries-dk/setup/top_loc.tcl

10. When you are ready to re-incorporate PR into the design, modify the PR region to be compatible with the new device. Refer to the Resize the Partial Reconfiguration Region section for instructions.

4.7 Modify the Memory Sub-System

OFS allows modifications on the Memory Sub-System in the FIM. This section provides an example walkthrough for modifiying the Memory-SS.

4.7.1 Walkthrough: Modify the Memory Sub-System Using IP Presets With OFSS

This walkthrough will go through the flow of modifying the Memory-SS in the OFS FIM. In this example, we will enable ECC on memory channels 0-3.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Run the setup stage of the build script to create a work directory with the Memory-SS configured for the iseries-dk

   ./ofs-common/scripts/common/syn/build_top.sh --stage setup iseries-dk work_iseries-dk
   

4. Open the Memory Subsystem mem_ss.ip in IP Parameter Editor

   qsys-edit $OFS_ROOTDIR/work_iseries-dk/ipss/mem/qip/mem_ss/mem_ss.ip
   

5. The Memory Subsystem IP will open in IP Parameter Editor. Click Dive Into Packaged Subsystem.

   

6. The Platform Designer mem_ss view opens. All of the EMIFs are shown in the Filter window.

   

7. Click each EMIF 0 through 3 and perform the following actions.

   1. In the Parameters window, click the Memory tab and change the DQ width to 72.

      

   2. In the Parameters window, click the Controller tab. Scroll down and check the box for Enable Error Detection and Correction Logic with ECC.

      

8. Once Step 6 has been done for each EMIF 0-3, click File -> Save. Close the Platform Designer window.

9. In the IP Parameter Editor Presets window, click New to create an IP Presets file.

   

10. In the New Preset window, set the Name for the preset to iseries-dk.

    

11. Click the ... button to select the location for the Preset file.

12. In the Save As window, change the save location to $OFS_ROOTDIR/ipss/mem/qip/presets and change the File Name to mem_presets.qprs to overwrite the existing presets file. Click OK.

    

13. Click Save in the New Preset window. Click No when prompted to add the file to the IP search path.

    

14. Close the IP Parameter Editor. You do not need to generate or save the IP.

15. Edit the $OFS_ROOTDIR/syn/board/iseries-dk/setup/emif_loc.tcl file to add pin assignments for the new signals supporting ECC on Channels 0-3.

    # CH0 DQS8
      set_location_assignment PIN_BC29 -to ddr4_mem[0].dbi_n[8]
      set_location_assignment PIN_AT30 -to ddr4_mem[0].dqs_n[8]
      set_location_assignment PIN_AV29 -to ddr4_mem[0].dqs[8]
      set_location_assignment PIN_AT28 -to ddr4_mem[0].dq[64]
      set_location_assignment PIN_AV27 -to ddr4_mem[0].dq[66]
      set_location_assignment PIN_AT32 -to ddr4_mem[0].dq[65]
      set_location_assignment PIN_BC31 -to ddr4_mem[0].dq[67]
      set_location_assignment PIN_BF32 -to ddr4_mem[0].dq[68]
      set_location_assignment PIN_AV31 -to ddr4_mem[0].dq[69]
      set_location_assignment PIN_BC27 -to ddr4_mem[0].dq[70]
      set_location_assignment PIN_BF28 -to ddr4_mem[0].dq[71]
    
      # CH1 DQS8
      set_location_assignment PIN_BC59 -to ddr4_mem[1].dbi_n[8]
      set_location_assignment PIN_AT60 -to ddr4_mem[1].dqs_n[8]
      set_location_assignment PIN_AV59 -to ddr4_mem[1].dqs[8]
      set_location_assignment PIN_BC61 -to ddr4_mem[1].dq[64]
      set_location_assignment PIN_AT62 -to ddr4_mem[1].dq[65]
      set_location_assignment PIN_AV61 -to ddr4_mem[1].dq[66]
      set_location_assignment PIN_BC57 -to ddr4_mem[1].dq[67]
      set_location_assignment PIN_BF62 -to ddr4_mem[1].dq[68]
      set_location_assignment PIN_AT58 -to ddr4_mem[1].dq[69]
      set_location_assignment PIN_BF58 -to ddr4_mem[1].dq[70]
      set_location_assignment PIN_AV57 -to ddr4_mem[1].dq[71]
    
      # CH2 DQS8
      set_location_assignment PIN_MD30 -to ddr4_mem[2].dbi_n[8]
      set_location_assignment PIN_MK31 -to ddr4_mem[2].dqs_n[8]
      set_location_assignment PIN_MH30 -to ddr4_mem[2].dqs[8]
      set_location_assignment PIN_MD32 -to ddr4_mem[2].dq[64]
      set_location_assignment PIN_MH32 -to ddr4_mem[2].dq[65]
      set_location_assignment PIN_MK33 -to ddr4_mem[2].dq[66]
      set_location_assignment PIN_MC33 -to ddr4_mem[2].dq[67]
      set_location_assignment PIN_MD28 -to ddr4_mem[2].dq[68]
      set_location_assignment PIN_MH28 -to ddr4_mem[2].dq[69]
      set_location_assignment PIN_MK29 -to ddr4_mem[2].dq[70]
      set_location_assignment PIN_MC29 -to ddr4_mem[2].dq[71]
    
      # CH3 DQS8
      set_location_assignment PIN_MD42 -to ddr4_mem[3].dbi_n[8]
      set_location_assignment PIN_MK43 -to ddr4_mem[3].dqs_n[8]
      set_location_assignment PIN_MH42 -to ddr4_mem[3].dqs[8]
      set_location_assignment PIN_MH40 -to ddr4_mem[3].dq[64]
      set_location_assignment PIN_MD40 -to ddr4_mem[3].dq[65]
      set_location_assignment PIN_MC41 -to ddr4_mem[3].dq[66]
      set_location_assignment PIN_MK41 -to ddr4_mem[3].dq[67]
      set_location_assignment PIN_MH44 -to ddr4_mem[3].dq[68]
      set_location_assignment PIN_MK45 -to ddr4_mem[3].dq[69]
      set_location_assignment PIN_MD44 -to ddr4_mem[3].dq[70]
      set_location_assignment PIN_MC45 -to ddr4_mem[3].dq[71]
    

16. Compile the design.

    ./ofs-common/scripts/common/syn/build_top.sh -p iseries-dk work_iseries-dk_mem_ecc_preset
    

4.7.2 Walkthrough: Add or remove the Memory Sub-System

The Memory Sub-System can be added or removed to the FIM design using the INCLUDE_DDR4 macro defined in the ofs_top.qsf file. The Memory-SS is enabled by default in the iseries-dk.

Pre-requisites:

• This walkthrough requires a development environment. Refer to the Set Up Development Environment Section for instructions on setting up a development environment.

Steps:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Edit the ofs_top.qsf file to either enable or disable the INCLUDE_DDR4 macro. Comment out this macro assignemnt if you wish to remove the Memory-SS.

4. Compile the design. Refer to the Compile OFS FIM section for step-by-step instructions.

4.8 Modify the Ethernet Sub-System

This section describes the flows for modifying the Ethernet Sub-System.

Note: The default HSSI-SS configuration for the iseries-dk is 2x4x25GbE.

4.8.1 Walkthrough: Modify the Ethernet Sub-System to 1x400GbE

OFS provides a preconfigured ofss file so the build script produces a FIM with a 1x400GbE Ethernet subsystem set for 400 GAUI-8. You can build this system with the following:

1. Clone the OFS PCIe Attach FIM repository (or use an existing cloned repository). Refer to the Clone FIM Repository section for step-by-step instructions.

2. Set development environment variables. Refer to the Set Development Environment Variables section for step-by-step instructions.

3. Build the I-Series FIM with 1x400GbE FIM:

   ./ofs-common/scripts/common/syn/build_top.sh -p --ofss tools/ofss_config/hssi/hssi_1x400_ftile.ofss iseries-dk work_iseries-dk_400
   

The resulting FIM with 1x400GbE has the following MAC settings:

Table: 1x400GbE MAC Settings

MAC Setting	Value
Client Interface	Segmented
FEC mode	IEEE 802.3 RS(544.514) (CL 134)
Auto Negotiation and link training	Disabled
Maximum Frame Size	1518

You can change the MAC settings by opening the Ethernet Subsystem IP in IP Parameter Editor, update the setting and then save the update as a new preset. You will then edit the ofss_config/hssi/hssi_1x400_ftile.ofss to use the new preset.

The following steps describe the steps to change the 400 GbE MAC frame size to 9600 bytes. Note, the 2x200 and 8x25 GbE MAC implementations can be changed using this process.

1. Invoke IP Parameter editor to make changes to the Ethernet Subsystem IP.

   cd $OFS_ROOTDIR/ipss/hssi/qip/hssi_ss
   qsys-edit hssi_ss.ip --quartus-project=$OFS_ROOTDIR/syn/board/iseries-dk/syn_top/ofs_top.qpf
   

2. In IP Parameter editor, load the 400g-fseries-dk preset by selecting and then click Apply

   

3. In the Device 0 Configuration tab, go to the F-Tile IP Configuration tab and scroll down to P8 MAC Options - P8 Basic and change the TX and RX maximum framesize to 9600.

   

4. Click New in the Presets panel and in the New Preset pop up window, Name the new preset 400g-fseries-dk-9600 and in File enter $OFS_ROOTDIR/ipss/hssi/qip/hssi_ss/presets/400g-fseries-dk-9600.qprs and click Save

   

5. Close IP Parameter Editor and do not save changes to hssi_ss.ip. The new preset captured the changes and this new preset will be used in the following updates to re-generate the Ethernet IP subsystem with the updated frame size.

6. Create a new ofss file for the new preset.

   cp $OFS_ROOTDIR/tools/ofss_config/hssi/hssi_1x400_ftile.ofss $OFS_ROOTDIR/tools/ofss_config/hssi/hssi_1x400_ftile_9600.ofss
   

7. Edit $OFS_ROOTDIR/tools/ofss_config/hssi/hssi_1x400_ftile_9600.ofss to use the new 400g-fseries-dk-9600 preset as listed below:

   [ip]
   type = hssi
   
   [settings]
   output_name = hssi_ss
   num_channels = 1
   data_rate = 400GAUI-8
   preset = 400g-fseries-dk-9600
   

8. Build the FIM with 9600 byte frame size by using the new hssi_1x400_ftile_9600.ofss file

   ./ofs-common/scripts/common/syn/build_top.sh -p --ofss tools/ofss_config/hssi/hssi_1x400_ftile_9600.ofss iseries-dk work_iseries-dk_400_9600
   

5. FPGA Configuration

Configuring the Agilex FPGA on the iseries-dk is done by programming a SOF image to the FPGA the embedded USvia JTAG using Quartus Programer.

5.1 Walkthrough: Set up JTAG

The Agilex® 7 FPGA I-Series Development Kit (2x R-Tile and 1xF-Tile) has an on-board FPGA Download Cable II module which is used to program the FPGA via JTAG.

Perform the following steps to establish a JTAG connection with the iseries-dk.

Pre-requisites:

• This walkthrough requires an OFS Agilex PCIe Attach deployment environment. Refer to the Getting Started Guide: OFS for Agilex® 7 PCIe Attach FPGAs (I-Series Development Kit (2xR-Tile, 1xF-Tile)) for instructions on setting up a deployment environment.

• This walkthrough requires a workstation with Quartus Prime Pro Version 24.1 tools installed, specifically the jtagconfig tool.

Steps:

1. Refer to the following figure showing the location of the on-board Intel FPGA Download Cable II micro USB connector.

   

2. Verify all switches are set to default as defined in Agilex® 7 FPGA I-Series Development Kit User Guide.

3. Connect a Micro-USB to USB-A cable between the front panel J8 micro USB port and either the deployment server or an external computer that has Quartus Prime Pro Programming tools installed.

4. Use the jtagconfig tool to check that the JTAG chain contains the AGIB027R29A1E2VR3 device.

   <QUARTUS_INSTALL_DIR>/24.1/quartus/bin/jtagconfig
   

   Example expected output:

   1) AGI FPGA Development Kit [1-13]
     034BB0DD   AGIB027R29A(.|R2|R3)/..
     020D10DD   VTAP10
   

5.2 Walkthrough: Program the FPGA via JTAG

This walkthrough describes the steps to program the Agilex FPGA on the Agilex® 7 FPGA I-Series Development Kit (2x R-Tile and 1xF-Tile) with a SOF image via JTAG.

Pre-Requisites:

• This walkthrough requires an OFS Agilex PCIe Attach deployment environment. Refer to the Getting Started Guide: OFS for Agilex® 7 PCIe Attach FPGAs (I-Series Development Kit (2xR-Tile, 1xF-Tile)) for instructions on setting up a deployment environment.

• This walkthrough requires a SOF image which will be programmed to the Agilex FPGA. Refer to the Compile OFS FIM Section for step-by-step instructions for generating a SOF image.

• This walkthrough requires a JTAG connection to the iseries-dk. Refer to the Set up JTAG section for step-by-step instructions.

• This walkthrough requires a Full Quartus Installation or Standalone Quartus Prime Programmer & Tools running on the machine where the Agilex® 7 FPGA I-Series Development Kit (2x R-Tile and 1xF-Tile) is connected via JTAG. The Quartus programmer version must be the same as the version of Quartus used to build the design.

Steps:

1. Start in your deployment environment.

2. If the card is already programmed with an OFS enabled design, determine the PCIe B:D.F of the card using OPAE command fpgainfo fme. In this example, the PCIe B:D.F is B1:00.0.

   fpgainfo fme
   

   Example output:

   Intel Acceleration JTAG PCI Development Kit
   //****** FME ******//
   Interface                        : DFL
   Object Id                        : 0xF100000
   PCIe s:b:d.f                     : 0000:B1:00.0
   Vendor Id                        : 0x8086
   Device Id                        : 0xBCCE
   SubVendor Id                     : 0x8086
   SubDevice Id                     : 0x0001
   Socket Id                        : 0x00
   Ports Num                        : 01
   Bitstream Id                     : 360571656856467345 
   Bitstream Version                : 5.0.1
   Pr Interface Id                  : b7855572-6ca9-58b8-bd11-44e1f1ab329f
   Boot Page                        : user
   

3. Remove the card from PCIe prior to programming. This will disable AER for the PCIe root port to prevent a surprise link-down event during programming.

   sudo pci_device 84:00.0 unplug
   

4. Switch to the machine with JTAG connection to the iseries-dk, if different than your deployment machine.

5. Open the Quartus programmer GUI

   Note: the Quartus programmer version must be the same as the version of Quartus used to build the design.

   quartus_pgmw
   

   

6. Click Hardware Setup to open the Hardware Setup dialog window.

   1. In the Currently selected hardware field select the iseries-dk.

   2. In the Hardware frequency field enter 16000000 Hz

      

   3. Click Close

7. In the Quartus Prime Programmer window, click Auto Detect.

8. If prompted, select the AGIB027R29A1E2VR3 device. The JTAG chain should show the device.

   

9. Right click the AGIB027R29A1E2VR3 row and selct Change File.

   

10. In the Select New Programming File window that opens, select the .sof image you wish to program and click Open.

11. Check the Program/Configure box for the AGIB027R29A1E2VR3 row, then click Start. Wait for the Progress bar to show 100% (Success).

    

12. Close the Quartus Programmer GUI.

13. Switch to the deployment environment, if different than the JTAG connected machine.

14. Replug the board PCIe

    sudo pci_device 84:00.0 plug
    

15. Run fpgainfo fme to verify communication with the board, and to check the PR Interface ID.

    Intel Acceleration JTAG PCI Development Kit
    //****** FME ******//
    Interface                        : DFL
    Object Id                        : 0xF100000
    PCIe s:b:d.f                     : 0000:B1:00.0
    Vendor Id                        : 0x8086
    Device Id                        : 0xBCCE
    SubVendor Id                     : 0x8086
    SubDevice Id                     : 0x0001
    Socket Id                        : 0x00
    Ports Num                        : 01
    Bitstream Id                     : 360571656856467345 
    Bitstream Version                : 5.0.1
    Pr Interface Id                  : b7855572-6ca9-58b8-bd11-44e1f1ab329f
    Boot Page                        : user
    

Appendix

Appendix A: Resource Utilization Tables

Table A-1 Default FIM Resource Utilization with PR (PCIe 1x16)

Compilation Hierarchy Node	ALMs needed	ALM Utilization %	M20Ks	M20K Utilization %
	261647.7	28.66	821	6.19
PCIE_RST_CTRL.rst_ctrl	465.6	0.05	0	0.0
afu_top	177715.5	19.47	393	2.96
auto_fab_0	1278.7	0.14	8	0.06
bpf	732.3	0.08	0	0.0
fme_top	625.1	0.07	6	0.05
hssi_wrapper	15867.4	1.74	80	0.6
local_mem_wrapper	10712.7	1.17	60	0.45
ofs_top_auto_tiles	7619.0	0.83	10	0.08
pcie_wrapper	44687.6	4.9	256	1.93
pmci_dummy_csr	682.6	0.07	0	0.0
qsfp_0	629.3	0.07	4	0.03
qsfp_1	629.0	0.07	4	0.03
sys_pll	0.5	0.0	0	0.0

Table A-2 Default FIM Resource Utilization with PR (PCIe 2x8)

Compilation Hierarchy Node	ALMs needed	ALM Utilization %	M20Ks	M20K Utilization %
	239719.6	26.26	840	6.33
PCIE_RST_CTRL.rst_ctrl	458.3	0.05	0	0.0
PCIE_RST_CTRL.rst_ctrl	79.0	0.01	0	0.0
afu_top	157249.2	17.23	309	2.33
auto_fab_0	1288.1	0.14	8	0.06
bpf	703.5	0.08	0	0.0
fme_top	626.6	0.07	6	0.05
hssi_wrapper	16164.1	1.77	80	0.6
local_mem_wrapper	10901.9	1.19	60	0.45
ofs_top_auto_tiles	7563.1	0.83	10	0.08
pcie_wrapper	42755.4	4.68	359	2.7
pmci_dummy_csr	676.5	0.07	0	0.0
qsfp_0	627.2	0.07	4	0.03
qsfp_1	624.0	0.07	4	0.03
sys_pll	0.5	0.0	0	0.0

Table A-3 Minimal FIM Resource Utilization (PCIe 2x8, 2PF)

Compilation Hierarchy Node	ALMs needed	ALM Utilization %	M20Ks	M20K Utilization %
	122157.7	13.38	598	4.51
PCIE_RST_CTRL.rst_ctrl	366.5	0.04	0	0.0
PCIE_RST_CTRL.rst_ctrl	65.4	0.01	0	0.0
afu_top	62450.5	6.84	190	1.43
auto_fab_0	1273.8	0.14	8	0.06
bpf	835.0	0.09	0	0.0
fme_top	614.6	0.07	6	0.05
hssi_dummy_csr	704.7	0.08	0	0.0
local_mem_wrapper	11229.5	1.23	60	0.45
pcie_wrapper	42541.4	4.66	334	2.52
pmci_dummy_csr	688.1	0.08	0	0.0
qsfp0_dummy_csr	697.4	0.08	0	0.0
qsfp1_dummy_csr	689.8	0.08	0	0.0
sys_pll	0.5	0.0	0	0.0

Appendix B: Glossary

Term	Abbreviation	Description
Advanced Error Reporting	AER	The PCIe AER driver is the extended PCI Express error reporting capability providing more robust error reporting. (link)
Accelerator Functional Unit	AFU	Hardware Accelerator implemented in FPGA logic which offloads a computational operation for an application from the CPU to improve performance. Note: An AFU region is the part of the design where an AFU may reside. This AFU may or may not be a partial reconfiguration region.
Basic Building Block	BBB	Features within an AFU or part of an FPGA interface that can be reused across designs. These building blocks do not have stringent interface requirements like the FIM's AFU and host interface requires. All BBBs must have a (globally unique identifier) GUID.
Best Known Configuration	BKC	The software and hardware configuration Intel uses to verify the solution.
Board Management Controller	BMC	Supports features such as board power managment, flash management, configuration management, and board telemetry monitoring and protection. The majority of the BMC logic is in a separate component, such as an Intel® Max® 10 or Intel Cyclone® 10 device; a small portion of the BMC known as the PMCI resides in the main Agilex FPGA.
Configuration and Status Register	CSR	The generic name for a register space which is accessed in order to interface with the module it resides in (e.g. AFU, BMC, various sub-systems and modules).
Data Parallel C++	DPC++	DPC++ is Intel’s implementation of the SYCL standard. It supports additional attributes and language extensions which ensure DCP++ (SYCL) is efficiently implanted on Intel hardware.
Device Feature List	DFL	The DFL, which is implemented in RTL, consists of a self-describing data structure in PCI BAR space that allows the DFL driver to automatically load the drivers required for a given FPGA configuration. This concept is the foundation for the OFS software framework. (link)
FPGA Interface Manager	FIM	Provides platform management, functionality, clocks, resets and standard interfaces to host and AFUs. The FIM resides in the static region of the FPGA and contains the FPGA Management Engine (FME) and I/O ring.
FPGA Management Engine	FME	Performs reconfiguration and other FPGA management functions. Each FPGA device only has one FME which is accessed through PF0.
Host Exerciser Module	HEM	Host exercisers are used to exercise and characterize the various host-FPGA interactions, including Memory Mapped Input/Output (MMIO), data transfer from host to FPGA, PR, host to FPGA memory, etc.
Input/Output Control	IOCTL	System calls used to manipulate underlying device parameters of special files.
Intel Virtualization Technology for Directed I/O	Intel VT-d	Extension of the VT-x and VT-I processor virtualization technologies which adds new support for I/O device virtualization.
Joint Test Action Group	JTAG	Refers to the IEEE 1149.1 JTAG standard; Another FPGA configuration methodology.
Memory Mapped Input/Output	MMIO	The memory space users may map and access both control registers and system memory buffers with accelerators.
oneAPI Accelerator Support Package	oneAPI-asp	A collection of hardware and software components that enable oneAPI kernel to communicate with oneAPI runtime and OFS shell components. oneAPI ASP hardware components and oneAPI kernel form the AFU region of a oneAPI system in OFS.
Open FPGA Stack	OFS	OFS is a software and hardware infrastructure providing an efficient approach to develop a custom FPGA-based platform or workload using an Intel, 3rd party, or custom board.
Open Programmable Acceleration Engine Software Development Kit	OPAE SDK	The OPAE SDK is a software framework for managing and accessing programmable accelerators (FPGAs). It consists of a collection of libraries and tools to facilitate the development of software applications and accelerators. The OPAE SDK resides exclusively in user-space.
Platform Interface Manager	PIM	An interface manager that comprises two components: a configurable platform specific interface for board developers and a collection of shims that AFU developers can use to handle clock crossing, response sorting, buffering and different protocols.
Platform Management Controller Interface	PMCI	The portion of the BMC that resides in the Agilex FPGA and allows the FPGA to communicate with the primary BMC component on the board.
Partial Reconfiguration	PR	The ability to dynamically reconfigure a portion of an FPGA while the remaining FPGA design continues to function. For OFS designs, the PR region is referred to as the pr_slot.
Port	N/A	When used in the context of the fpgainfo port command it represents the interfaces between the static FPGA fabric and the PR region containing the AFU.
Remote System Update	RSU	The process by which the host can remotely update images stored in flash through PCIe. This is done with the OPAE software command "fpgasupdate".
Secure Device Manager	SDM	The SDM is the point of entry to the FPGA for JTAG commands and interfaces, as well as for device configuration data (from flash, SD card, or through PCI Express* hard IP).
Static Region	SR	The portion of the FPGA design that cannot be dynamically reconfigured during run-time.
Single-Root Input-Output Virtualization	SR-IOV	Allows the isolation of PCI Express resources for manageability and performance.
SYCL	SYCL	SYCL (pronounced "sickle") is a royalty-free, cross-platform abstraction layer that enables code for heterogeneous and offload processors to be written using modern ISO C++ (at least C++ 17). It provides several features that make it well-suited for programming heterogeneous systems, allowing the same code to be used for CPUs, GPUs, FPGAs or any other hardware accelerator. SYCL was developed by the Khronos Group, a non-profit organization that develops open standards (including OpenCL) for graphics, compute, vision, and multimedia. SYCL is being used by a growing number of developers in a variety of industries, including automotive, aerospace, and consumer electronics.
Test Bench	TB	Testbench or Verification Environment is used to check the functional correctness of the Design Under Test (DUT) by generating and driving a predefined input sequence to a design, capturing the design output and comparing with-respect-to expected output.
Universal Verification Methodology	UVM	A modular, reusable, and scalable testbench structure via an API framework. In the context of OFS, the UVM enviroment provides a system level simulation environment for your design.
Virtual Function Input/Output	VFIO	An Input-Output Memory Management Unit (IOMMU)/device agnostic framework for exposing direct device access to userspace. (link)

Notices & Disclaimers

Intel<sup>®</sup> technologies may require enabled hardware, software or service activation. No product or component can be absolutely secure. Performance varies by use, configuration and other factors. Your costs and results may vary. You may not use or facilitate the use of this document in connection with any infringement or other legal analysis concerning Intel products described herein. You agree to grant Intel a non-exclusive, royalty-free license to any patent claim thereafter drafted which includes subject matter disclosed herein. No license (express or implied, by estoppel or otherwise) to any intellectual property rights is granted by this document, with the sole exception that you may publish an unmodified copy. You may create software implementations based on this document and in compliance with the foregoing that are intended to execute on the Intel product(s) referenced in this document. No rights are granted to create modifications or derivatives of this document. The products described may contain design defects or errors known as errata which may cause the product to deviate from published specifications. Current characterized errata are available on request. Intel disclaims all express and implied warranties, including without limitation, the implied warranties of merchantability, fitness for a particular purpose, and non-infringement, as well as any warranty arising from course of performance, course of dealing, or usage in trade. You are responsible for safety of the overall system, including compliance with applicable safety-related requirements or standards. <sup>©</sup> Intel Corporation. Intel, the Intel logo, and other Intel marks are trademarks of Intel Corporation or its subsidiaries. Other names and brands may be claimed as the property of others.

OpenCL and the OpenCL logo are trademarks of Apple Inc. used by permission of the Khronos Group™.